PMN5118UP Ericsson Power Modules, PMN5118UP Datasheet - Page 36

• Manufacturer Part Number: PMN5118UP
• Description: DC/DC Converters & Regulators 0.7-3.6V 30A Non-Iso Input 4.5-5.5V 108W
• Manufacturer: Ericsson Power Modules
• Series: PMNr

Specifications of PMN5118UP

• Output Power: 108 W
• Input Voltage Range: 4.5 V to 5.5 V
• Number Of Outputs: 1
• Output Voltage (channel 1): 0.7 V to 3.6 V
• Output Current (channel 1): 30 A
• Output Type: POLA Non-Isolated Regulator
• Product: Non-Isolated / POL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

E
Soldering Information — Through Hole Mounting
The through hole mount version of the product is intended for
manual or wave soldering. When wave soldering is used, the
temperature on the pins is specified to maximum 270 °C for
maximum 10 seconds.
A maximum preheat rate of 4°C/s and a temperature of max
of +150°C is suggested. When soldering by hand, care should
be taken to avoid direct contact between the hot soldering
iron tip and the pins for more than a few seconds in order to
prevent overheating.
A no-clean flux is recommended to avoid entrapment of
cleaning fluids in cavities inside the product or between the
product and the host board. The cleaning residues may affect
long time reliability and isolation voltage.
Delivery Package Information
The TH version products are delivered in antistatic trays.
The SMD version products are delivered in antistatic trays
and antistatic carrier tape (EIA 481 standard).
Prepared (also subject responsible if other)
EPANHON
Approved
SEC/D (Julia You)
PMN 5000 series
POL regulator, Input 4.5-5.5 V, Output up to 30 A/108 W
Tray Specifications
Material
Surface resistance
Tray capacity
Tray thickness
Box capacity
Bakability
Antistatic PET
10
35 products/tray
13 mm [0.512 inch]
175 products ( 5 full trays/box)
The tray is not bakable.
6
< Ohm/square < 10
12
Checked
See §1
Non-Dry Pack Information
The through hole mount version of product is delivered in
non-dry packing trays.
The lead (Pb) surface mount version of product is delivered in
non-dry packing trays or tape & reel.
Dry Pack Information
The lead free (Pb-free) surface mount version of the product
is delivered in trays or tape & reel. These inner shipment
containers are dry packed in standard moisture barrier bags
according to IPC/JEDEC standard J-STD-033 (Handling,
packing, shipping and use of moisture/reflow sensitivity
surface mount devices).
Using products in high temperature Pb-free soldering
processes requires dry pack storage and handling. In case
the products have been stored in an uncontrolled
environment and no longer can be considered dry, the
modules must be baked according to J-STD-033.
Ericsson Internal
PROD. SPEC. MECH.
No.
5/1301-BMR 656 Uen
Date
2007-06-25
Carrier Tape Specifications
Material
Surface resistance
Bakability
Tape width
Pocket pitch
Pocket depth
Reel diameter
Reel capacity
Technical Specification
EN/LZT 146 386 R1A
© Ericsson Power Modules AB
Rev
B
Antistatic PS
10
The tape is not bakable.
56 mm [2.205 inch]
24 mm [0.945 inch]
9.57 mm [0.377 inch]
381 mm [15 inch]
250 products /reel
7
< Ohm/square < 10
Reference
July 2007
12
2 (4)
36