WM8985GEFL Wolfson Microelectronics, WM8985GEFL Datasheet - Page 74

• Manufacturer Part Number: WM8985GEFL
• Description: Audio CODECs Multimedia CODEC with Class D HP
• Manufacturer: Wolfson Microelectronics

Specifications of WM8985GEFL

• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: QFN-32
• Minimum Operating Temperature: - 25 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

WM8985
w
ENABLING THE OUTPUTS
Table 39 Output Stages Power Management Control
THERMAL SHUTDOWN
Table 40 Thermal Shutdown
UNUSED ANALOGUE INPUTS/OUTPUTS
Each analogue output of the WM8985 can be independently enabled or disabled. The analogue
mixer associated with each output has a separate enable bit. All outputs are disabled by default. To
save power, unused parts of the WM8985 should remain disabled.
Outputs can be enabled at any time, but it is not recommended to do so when BUFIO is disabled
(BUFIOEN=0), as this may cause pop noise (see “Power Management” and “Applications
Information” sections).
Note: The SLEEP bit R2[6] should only be used when the device is already Standby mode. The
SLEEP bit prevents the MCLK from propagating round the device when the external MCLK signal
cannot be removed.
To protect the WM8985 from becoming too hot, a thermal sensor has been built in. If the device
junction temperature reaches approximately 125°C and the TSDEN and TSOPCTRL bit are set, then
all outputs will be disabled to avoid further increase of the chip temperature.
Additionally, when the device is too hot and TSDEN is set, then the WM8985 de-asserts GPIO bit
11, a virtual GPIO that can be set up to generate an interrupt to the CPU (see “GPIO and Interrupt
Control” section).
Whenever an analogue input/output is disabled, it remains connected to a voltage source (AVDD1/2)
through a resistor. This helps to prevent pop noise when the output is re-enabled. The resistance
between the voltage buffer and the output pins can be controlled using the VROI control bit. The
default impedance is low, so that any capacitors on the outputs can charge up quickly at start-up. If
a high impedance is desired for disabled outputs, VROI can then be set to 1, increasing the
resistance to about 30kΩ.
R1 (01h)
Power
Management
1
R2 (02h)
Power
Management
2
R3 (03h)
Power
Management
3
Note: All “Enable” bits are 1 = ON, 0 = OFF
R49 (31h)
Output Control
REGISTER
ADDRESS
REGISTER
ADDRESS
2
6
7
8
7
6
2
3
5
6
7
8
BIT
1
2
BIT
BUFIOEN
OUT3MIXEN
OUT4MIXEN
ROUT1EN
LOUT1EN
SLEEP
LMIXEN
RMIXEN
LOUT2EN
ROUT2EN
OUT3EN
OUT4EN
TSDEN
TSOPCTRL
LABEL
LABEL
0
0
0
0
0
0
0
0
0
0
0
0
0
0
DEFAULT
DEFAULT
Unused input/output bias buffer enable
OUT3 mixer enable
OUT4 mixer enable
ROUT1 output enable
LOUT1 output enable
0 = Normal device operation
1 = Supply current reduced in device
standby mode when clock supplied (see
note)
Left mixer enable
Right mixer enable
LOUT2 output enable
ROUT2 output enable
OUT3 enable
OUT4 enable
Thermal Sensor Enable
0 = disabled
1 = enabled
Thermal Shutdown Output enable
0 = Disabled
1 = Enabled, i.e. all outputs will be
disabled if TI set and the device junction
temperature is more than 125ºC.
DESCRIPTION
DESCRIPTION
PD, Rev 4.6, July 2009
Production Data
74