DLP-FLASH2 DLP Design Inc, DLP-FLASH2 Datasheet

Programmers & Debuggers DEVICE PROG/ INCIRCT DEBUGR W/ C COMPILER

DLP-FLASH2

Manufacturer Part Number

DLP-FLASH2

Description

Programmers & Debuggers DEVICE PROG/ INCIRCT DEBUGR W/ C COMPILER

Manufacturer

DLP Design Inc

Datasheet

1.DLP-FLASH2.pdf (5 pages)

Specifications of DLP-FLASH2

Positions/sockets

For Use With/related Products

PIC16F, PIC18F

Current page: 1 of 5
Download datasheet (161Kb)

1.0 INTRODUCTION

The DLP-FLASH2 is a complete in-circuit debugging and programming solution for Microchip's

PIC16Fxx and PIC18Fxx PIC® MCUs. The DLP-FLASH2 can debug all PIC16 and PIC18 targets

that support debug mode. It also provides in-circuit serial programming (ICSP) support for FLASH-

based PIC microcontrollers. The DLP-FLASH2 unit is compatible with the CCS PCW debugger or the

standalone ICD control software. The PCW debugger is integrated into the IDE of the PCW and

PCWH compilers and provides very detailed debugging information at the C level. The standalone

ICD control software ships with CCS compilers and allows you to quickly program target chips using

ICSP. The ICD control software also facilitates updating the DLP-FLASH2's firmware without having

to connect to a device programmer.

The DLP-FLASH2 allows in-circuit programming of target microcontrollers. All that is needed for

device programming on user target designs is a 6-pin header plus a few support components and

power isolation if the target electronics draw in excess of 300mA at 5 volts or operate at a voltage

other than 5 volts. The microcontroller can be soldered in place during the manufacturing process

and programmed at a later date to ensure that the final product is shipped with the most recent

firmware version.

NOTE: The DLP-FLASH2 only works with CCS Software. The MPLAB® IDE is not supported.

2.0 DLP-FLASH2 FEATURES

The DLP-FLASH2 is compatible with over 200 PIC microcontrollers. For a complete list of supported

devices, visit the CCS website:

•

Rev. 1.1 (September 2007)

No additional cables or external power source are required – all power is taken from the host USB

port.

USB based for compatibility with most PCs.

In-circuit programming; no more loading the target microcontroller into a device programmer.

http://www.ccsinfo.com/devices.php?page=icddevices

DLP-FLASH2

LEAD-FREE

Related parts for DLP-FLASH2

DLP-FLASH2 Summary of contents

Page 1

... NOTE: The DLP-FLASH2 only works with CCS Software. The MPLAB® IDE is not supported. 2.0 DLP-FLASH2 FEATURES The DLP-FLASH2 is compatible with over 200 PIC microcontrollers. For a complete list of supported devices, visit the CCS website: http://www.ccsinfo.com/devices.php?page=icddevices • ...

Page 2

... PC will immediately load the correct drivers without any prompting. Reboot the PC if prompted this point, the DLP-FLASH2 is ready for use. Run the CCS IDE software or the ICD control software. For additional information on how to use the CCS debugger, visit the CCS website: http://www ...

Page 3

... The DLP-FLASH2 is powered by the host’s USB port and requires approximately current for normal operation. If the target provides its own power or operates at a power supply voltage other than 5 volts, then the TPWR jumper must be removed and the target must be self-powered. ...

Page 4

... This product and its documentation are supplied on an as-is basis, and no warranty as to their suitability for any particular purpose is either made or implied. DLP Design will not accept any claim for damages whatsoever arising as a result of use or failure of this product. Your statutory rights are not affected ...

Page 5

VDD 5 15 GND VDD 6 GND ...

Related keywords

DLP-FLASH2 datasheet
DLP-FLASH2 data sheet
DLP-FLASH2 pdf datasheet
DLP-FLASH2 component
DLP-FLASH2 part
DLP-FLASH2 distributor
DLP-FLASH2 RoHS
DLP-FLASH2 datasheet download