DLP-232PC DLP Design Inc, DLP-232PC Datasheet
DLP-232PC
Specifications of DLP-232PC
Related parts for DLP-232PC
DLP-232PC Summary of contents
Page 1
... Small Footprint: 1.375 x 0.6 Inch PCB - Standard 18-Pin 0.3-Inch DIP Interface with 0.025 Square-Inch Posts - Easy to Use with Single-Byte Commands; Can Utilize a Simple Terminal Emulator to Control All Functions LEAD-FREE 5V 18-pin, 0.3-inch Interface Header for I/Os PIC 18F2410 © DLP Design, Inc ...
Page 2
... The programming interface (ICSP) is available for custom firmware development. 2.0 SPECIFICATIONS The DLP-232PC is a 5-volt system that derives its power from the host USB port. Each channel has the following capabilities: Digital Output: Set high, or clear to low. (The actual high/low voltage depends upon sink/source current ...
Page 3
... Manager. Right click on the entry under USB Controllers that appears when the DLP-232PC is connected, select Properties, select the Advanced tab, check the option for “Load VCP” and click OK. Once you unplug and then replug the DLP-232PC, a COM port should appear in Device Manager under Ports (COM & LPT). ...
Page 4
... Begin by opening the COM port, set the baud rate to 460800 (1 start bit, No parity, 8 data bits, 1 stop bit), and send single-byte commands as shown in Table 1. The Ping command can be used to locate the correct COM port used for communicating with the DLP-232PC, or you can look in Device Manager to see which port Windows has assigned to the DLP-232PC. ...
Page 5
... Dig Out – Low J 0x4A Digital Input M 0x4D Analog In [ 0x5B Temperature Channel 8 (Pin 15) Commands 8 0x38 Dig Out – High I 0x49 Dig Out – Low K 0x4B Digital Input , 0x2C Analog In (Comma) ] 0x5D Temperature Rev. 1.6 (October 2010) 5 © DLP Design, Inc. ...
Page 6
... Rev. 1.6 (October 2010) Default setting; nothing returned (Accent Grave character just left of the 1 key) Nothing returned Default setting; nothing returned Nothing returned Q (0x51) will be returned if the DLP-232PC is found on the selected port (Apostrophe character just right of the ; key) 6 © DLP Design, Inc. ...
Page 7
... TEMPERATURE DS18B20 digital temperature sensors can be connected to the DLP-232PC. For best performance, use Category 5 type computer cable to connect the sensors to the DLP-232PC. Two pairs of wires in the Cat 5 cable are required for the connection. The first pair is for Power (5V) and Ground, and the second pair is designated as Data and Ground ...
Page 8
... RETURN DATA TYPES By default, the DLP-232PC returns data to the host PC in the form of ASCII text such that it can be easily displayed and read using a simple terminal emulator. Alternatively, data can be returned in binary form requiring the user’s host app to calculate the voltage and temperature values. The commands used to set the return data types (0x60 and 0x5C) are shown at the end of Table 1 ...
Page 9
... This document provides preliminary information that may be subject to change without notice. 12.0 CONTACT INFORMATION DLP Design, Inc. 1605 Roma Lane Allen, TX 75013 Phone: 469-964-8027 Fax: 415-901-4859 Email Sales: sales@dlpdesign.com Email Support: support@dlpdesign.com Website URL: http://www.dlpdesign.com Rev. 1.6 (October 2010) 9 © DLP Design, Inc. ...
Page 10
GND 5 GND 1 24 AGND 4 GND 17 GND 20 GND 26 TEST 17 VDD 1 VCCIO ...