OM11042,598 NXP Semiconductors, OM11042,598 Datasheet - Page 13

• Manufacturer Part Number: OM11042,598
• Description: Microcontroller Modules & Accessories mbed LPC2368 Demo Board
• Manufacturer: NXP Semiconductors

Specifications of OM11042,598

• Product: Microcontroller Modules
• Data Bus Width: 32 bit
• Core Processor: LPC2368
• Clock Speed: 60 MHz
• Interface Type: Ethernet, CAN, I2C, SPI, UART
• Operating Supply Voltage: 3 V to 3.6 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

NXP Semiconductors
Table 4.
LPC2364_65_66_67_68_6
Product data sheet
Symbol
P2[1]/PWM1[2]/
RXD1/
PIPESTAT0
P2[2]/PWM1[3]/
CTS1/
PIPESTAT1
P2[3]/PWM1[4]/
DCD1/
PIPESTAT2
P2[4]/PWM1[5]/
DSR1/
TRACESYNC
P2[5]/PWM1[6]/
DTR1/
TRACEPKT0
P2[6]/PCAP1[0]/
RI1/
TRACEPKT1
P2[7]/RD2/
RTS1/
TRACEPKT2
P2[8]/TD2/
TXD2/
TRACEPKT3
P2[9]/
USB_CONNECT/
RXD2/EXTIN0
P2[10]/EINT0
Pin description
Pin
74
73
70
69
68
67
66
65
64
53
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[6]
…continued
Ball
B10
D8
E7
D9
D10
E8
E9
E10
F7
J10
[1]
[1]
[1]
[1]
[1]
[1]
[6]
[1]
[1]
[1]
Type
I/O
O
I
O
I/O
O
I
O
I/O
O
I
O
I/O
O
I
O
I/O
O
O
O
I/O
I
I
O
I/O
I
O
O
I/O
O
O
O
I/O
O
I
I
I/O
I
Description
P2[1] — General purpose digital input/output pin.
PWM1[2] — Pulse Width Modulator 1, channel 2 output.
RXD1 — Receiver input for UART1.
PIPESTAT0 — Pipeline Status, bit 0.
P2[2] — General purpose digital input/output pin.
PWM1[3] — Pulse Width Modulator 1, channel 3 output.
CTS1 — Clear to Send input for UART1.
PIPESTAT1 — Pipeline Status, bit 1.
P2[3] — General purpose digital input/output pin.
PWM1[4] — Pulse Width Modulator 1, channel 4 output.
DCD1 — Data Carrier Detect input for UART1.
PIPESTAT2 — Pipeline Status, bit 2.
P2[4] — General purpose digital input/output pin.
PWM1[5] — Pulse Width Modulator 1, channel 5 output.
DSR1 — Data Set Ready input for UART1.
TRACESYNC — Trace Synchronization.
P2[5] — General purpose digital input/output pin.
PWM1[6] — Pulse Width Modulator 1, channel 6 output.
DTR1 — Data Terminal Ready output for UART1.
TRACEPKT0 — Trace Packet, bit 0.
P2[6] — General purpose digital input/output pin.
PCAP1[0] — Capture input for PWM1, channel 0.
RI1 — Ring Indicator input for UART1.
TRACEPKT1 — Trace Packet, bit 1.
P2[7] — General purpose digital input/output pin.
RD2 — CAN2 receiver input. (LPC2364/66/68 only)
RTS1 — Request to Send output for UART1.
TRACEPKT2 — Trace Packet, bit 2.
P2[8] — General purpose digital input/output pin.
TD2 — CAN2 transmitter output. (LPC2364/66/68 only)
TXD2 — Transmitter output for UART2.
TRACEPKT3 — Trace Packet, bit 3.
P2[9] — General purpose digital input/output pin.
USB_CONNECT — Signal used to switch an external 1.5 kΩ resistor under
software control. Used with the SoftConnect USB feature. (LPC2364/66/68
only)
RXD2 — Receiver input for UART2.
EXTIN0 — External Trigger Input.
P2[10] — General purpose digital input/output pin.
Note: LOW on this pin while RESET is LOW forces on-chip bootloader to
take over control of the part after a reset.
EINT0 — External interrupt 0 input.
Rev. 06 — 1 February 2010
LPC2364/65/66/67/68
Single-chip 16-bit/32-bit microcontrollers
© NXP B.V. 2010. All rights reserved.
13 of 59