RXM-GPS-SG-T Linx Technologies Inc, RXM-GPS-SG-T Datasheet - Page 13

• Manufacturer Part Number: RXM-GPS-SG-T
• Description: GPS MODULE SMD SIRF
• Manufacturer: Linx Technologies Inc
• Series: SGr
• Type: GPS Moduler

Specifications of RXM-GPS-SG-T

• Package / Case: Module
• Operating Voltage: 4.2 V
• Operating Current: 46 mA
• Frequency Range: 1575.42 MHz
• Interface Type: UART, USB
• Operating Temperature Range: - 30 C to + 85 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Voltage - Supply: -
• Frequency: -
• Operating Temperature: -
• Applications: -
• Sensitivity: -
• Memory Size: -
• Data Interface: -
• Data Rate - Maximum: -
• Modulation Or Protocol: -
• Antenna Connector: -
• Current - Receiving: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Table 28: ReadInput Example
Table 29: ReadInput Response Example
Page 24
MID
GPIO
Number
Checksum
<CR> <LF>
MID
GPIO
Number
State
Checksum
<CR> <LF>
212 – ReadInput
n Read that GPIO 1 is low
n Read that GPIO 1 is high
n Read that GPIO 1 is not an input
The table below contains the values for the following example to read the state
of an input:
The receiver outputs a response to this command. The table below contains the
response for the above command:
For some further examples of this command:
Input command: $PLSC,212,1*0C
Output response: $PLSR,212,1,0*01
Input command: $PLSC,212,1*0C
Output response: $PLSR,212,1,1*00
Input command: $PLSC,212,1*0C
Output response: $PLSR,212,1,2*03
Name
Name
1
*0C
1
0
*01
$PLSC,212
$PLSR,212
Example
Example
Units
Units
$PLSC,212,1*0C
Message ID
Number of the GPIO line to read. Only
one line can be set at a time.
End of message termination
Message ID
Number of the GPIO line to set. Only one
line can be set at a time.
0 = Low; 1 = High; 2 = the referenced
GPIO is not an input
End of message termination
Description
Description
Table 30: WriteOutput Example
Table 31: WriteOutput Response Example
MID
GPIO
Number
State
Checksum
<CR> <LF>
MID
Valid
Checksum
<CR> <LF>
213 – WriteOutput
n Set GPIO 1 to low
n Set GPIO 1 to high
n GPIO 1 is not an output
The table below contains the values for the following example to write the state
of GPIO 1 to low:
The receiver outputs a response to this command. The table below contains the
response for the above command:
For some further examples of this command:
Input command: $PLSC,213,1,0*11
Output response: $PLSR,213,1*1C
Input command: $PLSC,213,1,1*10
Output response: $PLSR,213,1*1C
Input command: $PLSC,213,1,1*10
Output response: $PLSR,213,0*1D
Name
Name
1
0
*11
1
*1C
$PLSC,213
$PLSR,213
Example
Example
Units
Units
$PLSC,213,1,0*11
Message ID
Number of the GPIO line to write. Only
one line can be set at a time.
State; 0 = Low; 1 = High
End of message termination
Message ID
0: command invalid, 1: command valid
End of message termination
Description
Description
Page 25