XR88C681CP/40-F Exar Corporation, XR88C681CP/40-F Datasheet - Page 19

• Manufacturer Part Number: XR88C681CP/40-F
• Description: IC UART CMOS DUAL 40PDIP
• Manufacturer: Exar Corporation
• Type: CMOS Dual Channel UARTr

Specifications of XR88C681CP/40-F

• Number Of Channels: 2, DUART
• Package / Case: 40-DIP (0.600", 15.24mm)
• Features: *
• Fifo's: 1 Byte, 3 Byte
• Voltage - Supply: 5V
• With Parallel Port: Yes
• With Cmos: Yes
• Mounting Type: Through Hole
• Data Rate: 1 Mbps
• Supply Voltage (max): 5.25 V
• Supply Voltage (min): 4.75 V
• Supply Current: 15 mA
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: Through Hole
• Operating Supply Voltage: 5 V
• Propagation Delay Time Ns: 400 ns
• No. Of Channels: 2
• Supply Voltage Range: 4.75V To 5.25V
• Operating Temperature Range: 0°C To +70°C
• Digital Ic Case Style: DIP
• No. Of Pins: 40
• Filter Terminals: DIP
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 1016-1328-5

C. INTERRUPT CONTROL BLOCK
The Interrupt Control Block allows the user to apply the
DUART in an “Interrupt Driven” environment.
DUART includes an interrupt request output signal
(
the occurrence of any of the following events:
D Transmit Hold Register A or B Ready
D Receive Hold Register A or B Ready
The role and purpose of each of these registers are
defined here.
C.1 Interrupt Status Registers (ISR)
The contents of the ISR indicates the status of all potential
interrupt conditions. If any bits within these registers are
toggled “high”, then the corresponding condition has or is
The definition of the meaning behind each of these bits is
presented here.
ISR[7]: Input Port Change of State
If this bit is at a logic “1”, then a change of state was
detected at Input Port pins IP0 - IP3. The user would
service this interrupt by reading the IPCR (if ISR[7] = 1).
ISR[7] is cleared when the CPU has read the Input Port
Configuration Register (IPCR). By reading the IPCR, the
user will determine:
-
INTR), which may be programmed to be asserted upon
Input Port
Change
1 = Yes
0 = No
Rev. 2.11
Bit 7
Delta Break
1 = Yes
0 = No
Bit 6
B
Table 4. Listing and Brief Description of Interrupt System Registers
Register
MISR
IMR
ISR
IVR
FFULLB
RXRDY/
1 = Yes
0 = No
Bit 5
Masked Interrupt Status Register
Interrupt Status Register
Interrupt Vector Register
Interrupt Mask Register
Table 5. ISR Bit Format
TXRDYB
1 = Yes
0 = No
Bit 4
Description
The
19
D Receive FIFO A or B Full
D Start or End of Received Break in Channels A or B
D End of Counter/Timer Count Reached
D Change of State on input pins, IP0, IP1, IP2, IP3
The Interrupt Control Block consists of an Interrupt Status
Registers (ISR), an Interrupt Mask Registers (IMR), a
Masked Interrupt Status Registers (MISR) and an
Interrupt Vector Register (IVR).
registers, their address location (within the DUART).
occurring. In general, the contents of the ISR will indicate
to the processor, the source or the reason for the Interrupt
Request from the DUART.
service routine for the DUART should begin by reading
either this register or the MISR (Masked Interrupt Status
Register). The bit-format of the ISR is presented in
Table 5:
D The individual Input Port pin that changed state
D The final state of the monitored input ports, following
For a detailed description of the IPCR, see Section F.
Please note that in order to enable this Interrupt
Condition, the user must do two things:
1. Write the appropriate data to the lower nibble of the
Counter
1 = Yes
Ready
0 = No
Bit 3
the Change of State.
Auxiliary Control Register, ACR[3:0]. In this step, the
user is specifying which Input Pins should trigger an
“Input Port Change” Interrupt request.
Delta Break
(in DUART Address Space)
1 = Yes
0 = No
Bit 2
A
Address Location
05
05
02
16
16
16
(Read Only)
(Read Only)
(Write Only)
0C
XR88C681
16
FFULLA
RXRDY/
Therefore, any interrupt
1 = Yes
0 = No
Bit 1
Table 4 lists these
TXRDYA
1 = Yes
0 = No
Bit 0