AT91SAM7S512-MU-999 Atmel, AT91SAM7S512-MU-999 Datasheet - Page 507
AT91SAM7S512-MU-999
Manufacturer Part Number
AT91SAM7S512-MU-999
Description
IC MCU ARM7 512KB FLASH 64-VQFN
Manufacturer
Atmel
Series
AT91SAMr
Specifications of AT91SAM7S512-MU-999
Core Processor
ARM7
Core Size
16/32-Bit
Speed
55MHz
Connectivity
I²C, SPI, SSC, UART/USART, USB
Peripherals
Brown-out Detect/Reset, DMA, POR, PWM, WDT
Number Of I /o
32
Program Memory Size
512KB (512K x 8)
Program Memory Type
FLASH
Ram Size
64K x 8
Voltage - Supply (vcc/vdd)
1.65 V ~ 1.95 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-VQFN Exposed Pad, 64-HVQFN, 64-SQFN, 64-DHVQFN
For Use With
AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7S-EK - KIT EVAL FOR ARM AT91SAM7S
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
- Current page: 507 of 779
- Download datasheet (11Mb)
Figure 35-8. Data IN Transfer for Ping-pong Endpoint
6175K–ATARM–30-Aug-10
TXPKTRDY Flag
(UDP_MCSRx)
FIFO (DPR)
Bank 0
USB Bus
Packets
TXCOMP Flag
(UDP_CSRx)
FIFO (DPR)
Bank 1
Written by
Microcontroller
Microcontroller
Load Data IN Bank 0
Set by Firmware,
Data Payload Written in FIFO Bank 0
Warning: There is software critical path due to the fact that once the second bank is filled, the
driver has to wait for TX_COMP to set TX_PKTRDY. If the delay between receiving TX_COMP
is set and TX_PKTRDY is set too long, some Data IN packets may be NACKed, reducing the
bandwidth.
Warning: TX_COMP must be cleared after TX_PKTRDY has been set.
1. The microcontroller checks if it is possible to write in the FIFO by polling TXPKTRDY to
2. The microcontroller writes the first data payload to be sent in the FIFO (Bank 0), writing
3. The microcontroller notifies the USB peripheral it has finished writing in Bank 0 of the
4. Without waiting for TXPKTRDY to be cleared, the microcontroller writes the second
5. The microcontroller is notified that the first Bank has been released by the USB device
6. Once the microcontroller has received TXCOMP for the first Bank, it notifies the USB
7. At this step, Bank 0 is available and the microcontroller can prepare a third data pay-
Data IN
PID
be cleared in the endpoint’s UDP_ CSRx register.
zero or more byte values in the endpoint’s UDP_ FDRx register.
FIFO by setting the TXPKTRDY in the endpoint’s UDP_ CSRx register.
data payload to be sent in the FIFO (Bank 1), writing zero or more byte values in the
endpoint’s UDP_ FDRx register.
when TXCOMP in the endpoint’s UDP_ CSRx register is set. An interrupt is pending
while TXCOMP is being set.
device that it has prepared the second Bank to be sent, raising TXPKTRDY in the end-
point’s UDP_ CSRx register.
load to be sent
Microcontroller Load Data IN Bank 1
USB Device Send Bank 0
Written by
Microcontroller
Read by USB Device
Data IN
Cleared by USB Device,
Data Payload Fully Transmitted
.
Set by USB
Device
AT91SAM7S Series Preliminary
ACK
PID
Interrupt Cleared by Firmware
Data IN
PID
Microcontroller Load Data IN Bank 0
USB Device Send Bank 1
Interrupt Pending
Written by
Microcontroller
Set by Firmware,
Data Payload Written in FIFO Bank 1
Read by USB Device
Data IN
Set by USB Device
ACK
PID
507
Related parts for AT91SAM7S512-MU-999
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
DEV KIT FOR AVR/AVR32
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: