ATMEGA64-16AI Atmel, ATMEGA64-16AI Datasheet - Page 188

• Manufacturer Part Number: ATMEGA64-16AI
• Description: IC AVR MCU 64K 16MHZ IND 64-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA64-16AI

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Using MPCM
USART Register
Description
UDRn – USART I/O
Data Register
2490Q–AVR–06/10
addressed. If a particular Slave MCU has been addressed, it will receive the following data
frames as normal, while the other slave MCUs will ignore the received frames until another
address frame is received.
For an MCU to act as a Master MCU, it can use a 9-bit character frame format (UCSZn = 7). The
ninth bit (TXB8n) must be set when an address frame (TXB8n = 1) or cleared when a data frame
(TXBn = 0) is being transmitted. The Slave MCUs must in this case be set to use a 9-bit charac-
ter frame format.
The following procedure should be used to exchange data in Multi-processor Communication
mode:
1. All Slave MCUs are in Multi-processor Communication mode (MPCMn in UCSRnA is
2. The Master MCU sends an address frame, and all slaves receive and read this frame. In
3. Each Slave MCU reads the UDRn Register and determines if it has been selected. If so,
4. The addressed MCU will receive all data frames until a new address frame is received.
5. When the last data frame is received by the addressed MCU, the addressed MCU sets
Using any of the 5-bit to 8-bit character frame formats is possible, but impractical since the
Receiver must change between using n and n+1 character frame formats. This makes full
duplex operation difficult since the Transmitter and Receiver uses the same character size set-
ting. If 5-bit to 8-bit character frames are used, the Transmitter must be set to use two stop bit
(USBSn = 1) since the first stop bit is used for indicating the frame type.
Do not use Read-Modify-Write instructions (SBI and CBI) to set or clear the MPCM bit. The
MPCMn bit shares the same I/O location as the TXCn flag and this might accidentally be cleared
when using SBI or CBI instructions.
The USART Transmit Data Buffer Register and USART Receive Data Buffer Registers share the
same I/O address referred to as USART Data Register or UDRn. The Transmit Data Buffer Reg-
ister (TXBn) will be the destination for data written to the UDRn Register location. Reading the
UDRn Register location will return the contents of the Receive Data Buffer Register (RXBn).
For 5-bit, 6-bit, or 7-bit characters the upper unused bits will be ignored by the Transmitter and
set to zero by the Receiver.
The transmit buffer can only be written when the UDREn flag in the UCSRnA Register is set.
Data written to UDRn when the UDREn flag is not set, will be ignored by the USART transmitter.
When data is written to the transmit buffer, and the Transmitter is enabled, the Transmitter will
Bit
Read/Write
Initial Value
set).
the Slave MCUs, the RXCn flag in UCSRnA will be set as normal.
it clears the MPCMn bit in UCSRnA, otherwise it waits for the next address byte and
keeps the MPCMn setting.
The other Slave MCUs, which still have the MPCMn bit set, will ignore the data frames.
the MPCMn bit and waits for a new address frame from Master. The process then
repeats from 2.
R/W
7
0
R/W
6
0
R/W
5
0
R/W
4
0
RXB[7:0]
TXB[7:0]
R/W
3
0
R/W
2
0
R/W
1
0
R/W
ATmega64(L)
0
0
UDnR (Read)
UDnR (Write)
188