SAB-C161O-LM 3V HA Infineon Technologies, SAB-C161O-LM 3V HA Datasheet - Page 11

• Manufacturer Part Number: SAB-C161O-LM 3V HA
• Description: IC MICROCONTROLLER 16BIT MQFP80
• Manufacturer: Infineon Technologies
• Series: C16xxr

Specifications of SAB-C161O-LM 3V HA

• Core Processor: C166
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: EBI/EMI, SPI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 63
• Program Memory Type: ROMless
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 80-SQFP
• Data Bus Width: 16 bit
• Data Ram Size: 2 KB
• Interface Type: 1xASC, 1xSSC
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 63
• Number Of Timers: 5
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• Packages: PG-MQFP-80
• Max Clock Frequency: 20.0 MHz
• Sram (incl. Cache): 2.0 KByte
• Program Memory: 0.0 KByte
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details
• Other names: B161OLM3VHAXT; SABC161OLM3VHAXT; SP000011588

Table 2
Symbol Pin
RSTIN
RST
OUT
NMI
P6
P6.0
P6.1
P6.2
P6.3
Data Sheet
Num
65
66
67
68
69
70
71
Pin Definitions and Functions (cont’d)
Input
Outp.
I/O
O
I
IO
O
O
O
O
Function
Reset Input with Schmitt-Trigger characteristics. A low level
at this pin while the oscillator is running resets the C161K/O.
An internal pullup resistor permits power-on reset using only
a capacitor connected to
pulses < 10 ns. Input pulses >100 ns safely pass the filter.
The minimum duration for a safe recognition should be
100 ns + 2 CPU clock cycles.
In bidirectional reset mode (enabled by setting bit BDRSTEN
in register SYSCON) the RSTIN line is internally pulled low
for the duration of the internal reset sequence upon any reset
(HW, SW, WDT). See note below this table.
Note: To let the reset configuration of PORT0 settle a reset
Internal Reset Indication Output. This pin is set to a low level
when the part is executing either a hardware-, a software- or
a watchdog timer reset. RSTOUT remains low until the EINIT
(end of initialization) instruction is executed.
Non-Maskable Interrupt Input. A high to low transition at this
pin causes the CPU to vector to the NMI trap routine. When
the PWRDN (power down) instruction is executed, the NMI
pin must be low in order to force the C161K/O to go into
power down mode. If NMI is high, when PWRDN is
executed, the part will continue to run in normal mode.
If not used, pin NMI should be pulled high externally.
Port 6 is a 4-bit bidirectional I/O port. It is bit-wise
programmable for input or output via direction bits. For a pin
configured as input, the output driver is put into high-
impedance state. Port 6 outputs can be configured as push/
pull or open drain drivers.
The Port 6 pins also serve for alternate functions:
CS0
CS1
CS2
CS3
These chip select outputs are only available in the C161O.
duration of ca. 1 ms is recommended.
Chip Select 0 Output
Chip Select 1 Output
Chip Select 2 Output
Chip Select 3 Output
7
V
SS
. A spike filter suppresses input
V2.0, 2001-01
C161O
C161K