M30263F6AFP#U5A Renesas Electronics America, M30263F6AFP#U5A Datasheet - Page 141

• Manufacturer Part Number: M30263F6AFP#U5A
• Description: IC M16C/26A MCU FLASH 42-SSOP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/26r

Specifications of M30263F6AFP#U5A

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, PWM, Voltage Detect, WDT
• Number Of I /o: 33
• Program Memory Size: 48KB (48K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 42-SSOP
• For Use With: R0K33026AS000BE - KIT DEV EVALUATION M16C/26A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

R
R
M
e
E
1
. v
J
Figure 12.3.5. TA1, TA2, TA4, TA11, TA21 and TA41 Registers
6
0
2
C
9
0 .
B
2 /
0
0
6
2
A
0
F
2
e
G
0 -
b
1 .
o r
Timer Ai, Ai-1 register (i=1, 2, 4)
2
(b15)
b7
NOTES:
0
, 5
u
0
p
1. The register must be accessed in 16 bit units.
2. When the timer Ai register is set to "0000
3.Use MOV instruction to write to these registers.
4. If the INV15 bit is "0" (dead time timer enable), the positive or negative phase whichever is going from an
5. If the INV11 bit is "0" (three-phase mode 0), the TAi register value is transferred to the reload register by a
6. Do not write to TAi1 registers synchronously with a timer B2 underflow In three-phase mode 1.
7. Write to the TAi1 register as follows:
2
0
(
occur.
inactive to an active level changes at the same time the dead time timer stops.
timer Ai (i = 1, 2 or 4) start trigger. If the INV11 bit is "1" (three-phase mode 1), the TAi1 register value is
transferred to the reload register by a timer Ai start trigger first and then the TAi register value is transferred
to the reload register by the next timer Ai start trigger. Thereafter, the TAi1 register and TAi register values
are transferred to the reload register alternately.
(1) Write a value to the TAi1 register
(2) Wait for one cycle of timer Ai count source.
(3) Write the same value to the TAi1 register again.
M
0
7
1
6
C
page 122
2 /
6
(b8)
, A
b0 b7
M
1
f o
6
C
3
Assuming the set value = n, upon a start trigger the timer
starts counting the count source and stops after counting
it n times. The positive and negative phases change at
the same time timer A, A2 or A4 stops.
2
2 /
9
6
, B
M
b0
1
(1, 2, 3, 4, 5)
6
C
2 /
16
", the counter does not operate and a timer Ai interrupt does not
6
Symbol
) T
TA1
TA2
TA4
TA11
TA21
TA41
Function
(6,7)
(6,7)
(6,7)
038B
038F
0389
0343
0345
0347
Address
16
16
16
16
16
16
-0388
-038A
-038E
-0342
-0344
-0346
16
16
16
16
16
16
0000
Setting range
After reset
16
Indeterminate
Indeterminate
Indeterminate
Indeterminate
Indeterminate
Indeterminate
to FFFF
16
WO
RW
12. Timer