MC9S08GT16ACFBE Freescale Semiconductor, MC9S08GT16ACFBE Datasheet - Page 176

• Manufacturer Part Number: MC9S08GT16ACFBE
• Description: IC MCU 16K FLASH 2K RAM 44-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08GT16ACFBE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFP
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: I2C/SCI/SPI
• Total Internal Ram Size: 2KB
• # I/os (max): 36
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: PQFP
• Processor Series: S08GT
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Operating Supply Voltage: 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: M68EVB908GB60E, M68DEMO908GB60E
• Minimum Operating Temperature: - 40 C
• For Use With: M68DEMO908GB60E - BOARD DEMO MC9S08GB60M68EVB908GB60E - BOARD EVAL FOR MC9S08GB60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Serial Communications Interface (S08SCIV1)
11.2.3
This register can be read or written at any time.
176
Reset
Field
TCIE
ILIE
TIE
RIE
RE
TE
7
6
5
4
3
2
W
R
SCI Control Register 2 (SCIxC2)
TIE
Transmit Interrupt Enable (for TDRE)
0 Hardware interrupts from TDRE disabled (use polling).
1 Hardware interrupt requested when TDRE flag is 1.
Transmission Complete Interrupt Enable (for TC)
0 Hardware interrupt requested when TC flag is 1.
1 Hardware interrupts from TC disabled (use polling).
Receiver Interrupt Enable (for RDRF)
0 Hardware interrupts from RDRF disabled (use polling).
1 Hardware interrupt requested when RDRF flag is 1.
Idle Line Interrupt Enable (for IDLE)
0 Hardware interrupts from IDLE disabled (use polling).
1 Hardware interrupt requested when IDLE flag is 1.
Transmitter Enable
0 Transmitter off.
1 Transmitter on.
TE must be 1 in order to use the SCI transmitter. Normally, when TE = 1, the SCI forces the TxD pin to act as an
output for the SCI system. If LOOPS = 1 and RSRC = 0, the TxD pin reverts to being a port B general-purpose
I/O pin even if TE = 1.
When the SCI is configured for single-wire operation (LOOPS = RSRC = 1), TXDIR controls the direction of
traffic on the single SCI communication line (TxD pin).
TE also can be used to queue an idle character by writing TE = 0 then TE = 1 while a transmission is in progress.
Refer to
When TE is written to 0, the transmitter keeps control of the port TxD pin until any data, queued idle, or queued
break character finishes transmitting before allowing the pin to revert to a general-purpose I/O pin.
Receiver Enable — When the SCI receiver is off, the RxD pin reverts to being a general-purpose port I/O pin.
0 Receiver off.
1 Receiver on.
0
7
Section 11.3.2.1, “Send Break and Queued
TCIE
0
6
Table 11-4. SCIxC2 Register Field Descriptions
Figure 11-7. SCI Control Register 2 (SCIxC2)
MC9S08GT16A/GT8A Data Sheet, Rev. 1
RIE
0
5
ILIE
0
4
Description
Idle,” for more details.
TE
3
0
RE
0
2
Freescale Semiconductor
RWU
0
1
SBK
0
0