STM32F103RET6TR STMicroelectronics, STM32F103RET6TR Datasheet - Page 41
![MCU ARM 32BIT 512KB FLASH 64LQFP](/photos/12/15/121504/stmicroelectronics-64-lqfp_sml.jpg)
STM32F103RET6TR
Manufacturer Part Number
STM32F103RET6TR
Description
MCU ARM 32BIT 512KB FLASH 64LQFP
Manufacturer
STMicroelectronics
Series
STM32r
Datasheet
1.STM32F103VCT6.pdf
(123 pages)
Specifications of STM32F103RET6TR
Core Processor
ARM® Cortex-M3™
Core Size
32-Bit
Speed
72MHz
Connectivity
CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
Peripherals
DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
Number Of I /o
51
Program Memory Size
512KB (512K x 8)
Program Memory Type
FLASH
Ram Size
64K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Data Converters
A/D 16x12b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-LQFP
For Use With
497-10508 - BOARD EVAL FOR MEMS SENSORS497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32KSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STM32F103RET6TR
Manufacturer:
ST
Quantity:
872
Company:
Part Number:
STM32F103RET6TR
Manufacturer:
STMicroelectronics
Quantity:
10 000
STM32F103xC, STM32F103xD, STM32F103xE
5.2
Absolute maximum ratings
Stresses above the absolute maximum ratings listed in
Table 8: Current
damage to the device. These are stress ratings only and functional operation of the device
at these conditions is not implied. Exposure to maximum rating conditions for extended
periods may affect device reliability.
Table 7.
1. All main power (V
2. I
Table 8.
1. All main power (V
2. I
3. Negative injection disturbs the analog performance of the device. See note in
4. When several inputs are submitted to a current injection, the maximum I
|V
V
I
V
INJ(PIN)
I
supply, in the permitted range.
maximum is respected. If V
externally to the I
induced by V
supply, in the permitted range.
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
characteristics.
positive and negative injected currents (instantaneous values). These results are based on
characterization with I
Symbol
SSX
INJ(PIN)
INJ(PIN)
|V
ESD(HBM)
DD
Symbol
INJ(PIN)
V
I
I
–V
VDD
DDx
VSS
I
IN
V
IO
SS
must never be exceeded (see
(2)(3)
must never be exceeded. This is implicitly insured if V
|
SS
(2)
|
Voltage characteristics
Current characteristics
IN
External main supply voltage (including V
and V
Input voltage on five volt tolerant pin
Input voltage on any other pin
Variations between different V
Variations between all the different ground pins
Electrostatic discharge voltage (human body
model)
< V
characteristics, and
Total current into V
Total current out of V
Output current sunk by any I/O and control pin
Output current source by any I/Os and control pin
Injected current on NRST pin
Injected current on HSE OSC_IN and LSE OSC_IN pins
Injected current on any other pin
Total injected current (sum of all I/O and control pins)
INJ(PIN)
DD
DD
SS
, V
, V
DD
.
DDA
DDA
INJ(PIN)
)
IN
value. A positive injection is induced by V
(1)
> V
) and ground (V
) and ground (V
IN
maximum cannot be respected, the injection current must be limited
DD
maximum current injection on four I/O port pins of the device.
while a negative injection is induced by V
Doc ID 14611 Rev 7
Ratings
DD
Table 8: Current
SS
/V
Table 9: Thermal characteristics
SS
SS
DDA
ground lines (sink)
, V
, V
Ratings
SSA
SSA
(2)
power lines (source)
DD
) pins must always be connected to the external power
) pins must always be connected to the external power
power pins
(4)
(2)
characteristics). This is implicitly insured if V
DDA
IN
maximum is respected. If V
(1)
Table 7: Voltage
IN
> V
see
Absolute maximum ratings
(electrical sensitivity)
(1)
IN
V
V
INJ(PIN)
max while a negative injection is
SS
SS
IN
Section 5.3.12:
–0.3
INJ(PIN)
Min
(4)
< V
Electrical characteristics
0.3
0.3
Section 5.3.18: 12-bit ADC
is the absolute sum of the
SS
may cause permanent
.
value. A positive
characteristics,
V
Max.
25
± 25
150
150
± 5
± 5
± 5
DD
25
Max
+5.5
IN
4.0
50
50
+0.3
maximum
IN
Unit
41/123
mA
Unit
mV
V