P89LPC9151FDH,129 NXP Semiconductors, P89LPC9151FDH,129 Datasheet - Page 53

• Manufacturer Part Number: P89LPC9151FDH,129
• Description: IC 80C51 MCU FLASH 2KB 14TSSOP
• Manufacturer: NXP Semiconductors
• Series: LPC900r

Specifications of P89LPC9151FDH,129

• Program Memory Type: FLASH
• Program Memory Size: 2KB (2K x 8)
• Package / Case: 14-TSSOP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 18MHz
• Connectivity: I²C, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 12
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 4x8b; D/A 1x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: P89LPC
• Core: 80C51
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SPI
• Maximum Clock Frequency: 18 MHz
• Number Of Programmable I/os: 10
• Number Of Timers: 2
• Operating Supply Voltage: 2.4 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 4 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 935290259129

NXP Semiconductors
P89LPC9151_61_71_2
Product data sheet
Fig 15. SPI block diagram
SPI STATUS REGISTER
BY 4, 16, 64, 128
CPU clock
DIVIDER
SELECT
SPI CONTROL
7.23 SPI (P89LPC9161)
The P89LPC9161 provides another high-speed serial communication interface: the SPI
interface. SPI is a full-duplex, high-speed, synchronous communication bus with two
operation modes: Master mode and Slave mode. Up to 3 Mbit/s can be supported in either
Master mode or Slave mode. It has a Transfer Completion Flag and Write Collision Flag
Protection.
The SPI interface has four pins: SPICLK, MOSI, MISO and SS:
Typical connections are shown in
•
•
SPICLK, MOSI and MISO are typically tied together between two or more SPI
devices. Data flows from master to slave on MOSI (Master Out Slave In) pin and flows
from slave to master on MISO (Master In Slave Out) pin. The SPICLK signal is output
in the Master mode and is input in the Slave mode. If the SPI system is disabled, i.e.,
SPEN (SPCTL.6) = 0 (reset value), these pins are configured for port functions.
SS is the optional slave select pin. In a typical configuration, an SPI master asserts
one of its port pins to select one SPI device as the current slave. An SPI slave device
uses its SS pin to determine whether it is selected.
interrupt
request
SPI clock (master)
SPI
MSTR
SPEN
Rev. 02 — 9 February 2010
internal
data
bus
SPI CONTROL REGISTER
8-BIT SHIFT REGISTER
READ DATA BUFFER
CLOCK LOGIC
Figure 16
P89LPC9151/9161/9171
clock
through
8-bit microcontroller with 8-bit ADC
Figure
18.
M
M
M
S
S
S
CONTROL
LOGIC
PIN
© NXP B.V. 2010. All rights reserved.
002aaa900
MISO
P2.3
MOSI
P2.2
SPICLK
P2.5
SS
P2.4
53 of 91