DSPIC30F5016-20E/PT Microchip Technology, DSPIC30F5016-20E/PT Datasheet - Page 163
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
DSPIC30F5016-20E/PT
Manufacturer Part Number
DSPIC30F5016-20E/PT
Description
IC DSPIC MCU/DSP 66K 80TQFP
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F2011-20ISO.pdf
(66 pages)
2.DSPIC30F2011-20IP.pdf
(26 pages)
3.DSPIC30F5016-30IPT.pdf
(230 pages)
4.DSPIC30F5016-30IPT.pdf
(14 pages)
5.DSPIC30F5016-30IPT.pdf
(6 pages)
6.DSPIC30F5016-30IPT.pdf
(18 pages)
Specifications of DSPIC30F5016-20E/PT
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
CAN, I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
Number Of I /o
68
Program Memory Size
66KB (22K x 24)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
80-TFQFP
For Use With
AC164320 - MODULE SKT MPLAB PM3 80TQFPAC30F007 - MODULE SKT FOR DSPIC30F 80TQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F5016-20E/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
22.0
The
enhancements to the previous PIC
(MCU) instruction sets, while maintaining an easy
migration from PIC MCU instruction sets.
Most instructions are a single program memory word
(24 bits). Only three instructions require two program
memory locations.
Each single-word instruction is a 24-bit word divided
into an 8-bit opcode which specifies the instruction
type, and one or more operands which further specify
the operation of the instruction.
The instruction set is highly orthogonal and is grouped
into five basic categories:
• Word or byte-oriented operations
• Bit-oriented operations
• Literal operations
• DSP operations
• Control operations
Table 22-1 shows the general symbols used in
describing the instructions.
The dsPIC30F instruction set summary in Table 22-2
lists all the instructions along with the status flags
affected by each instruction.
Most word or byte-oriented W register instructions
(including
operands:
• The first source operand, which is typically a
• The second source operand, which is typically a
• The destination of the result, which is typically a
However, word or byte-oriented file register
instructions have two operands:
• The file register specified by the value ‘f’
• The destination, which could either be the file
© 2008 Microchip Technology Inc.
Note:
register ‘Wb’ without any address modifier
register ‘Ws’ with or without an address modifier
register ‘Wd’ with or without an address modifier
register ‘f’ or the W0 register, which is denoted as
‘WREG’
dsPIC30F
INSTRUCTION SET SUMMARY
This data sheet summarizes features of
this group of dsPIC30F devices and is not
intended to be a complete reference
source. For more information on the CPU,
peripherals, register descriptions and
general device functionality, refer to the
“dsPIC30F Family Reference Manual”
(DS70046). For more information on the
device instruction set and programming,
refer to the “dsPIC30F/33F Programmer’s
Reference Manual” (DS70157).
barrel
shift
instruction
instructions)
set
®
Microcontroller
adds
have
many
three
Most bit oriented instructions (including simple
rotate/shift instructions) have two operands:
• The W register (with or without an address
• The bit in the W register or file register
The literal instructions that involve data movement may
use some of the following operands:
• A literal value to be loaded into a W register or file
• The W register or file register where the literal
However, literal instructions that involve arithmetic or
logical operations use some of the following operands:
• The first source operand, which is a register ‘Wb’
• The second source operand, which is a literal
• The destination of the result (only if not the same
The MAC class of DSP instructions may use some of the
following operands:
• The accumulator (A or B) to be used (required
• The W registers to be used as the two operands
• The X and Y address space prefetch operations
• The X and Y address space prefetch destinations
• The accumulator write-back destination
The other DSP instructions do not involve any
multiplication, and may include:
• The accumulator to be used (required)
• The source or destination operand (designated as
• The amount of shift, specified by a W register ‘Wn’
The control instructions may use some of the following
operands:
• A program memory address
• The mode of the table read and table write
All instructions are a single word, except for certain
double-word
double-word instructions so that all the required
information is available in these 48 bits. In the second
word, the 8 MSbs are ‘0’s. If this second word is
executed as an instruction (by itself), it will execute as
a NOP.
modifier) or file register (specified by the value of
‘Ws’ or ‘f’)
(specified by a literal value, or indirectly by the
contents of register ‘Wb’)
register (specified by the value of ‘k’)
value is to be loaded (specified by ‘Wb’ or ‘f’)
without any address modifier
value
as the first source operand), which is typically a
register ‘Wd’ with or without an address modifier
operand)
Wso or Wdo, respectively) with or without an
address modifier
or a literal value
instructions
dsPIC30F5015/5016
instructions,
which
DS70149D-page 163
were
made