PIC18F2431-I/SO Microchip Technology, PIC18F2431-I/SO Datasheet - Page 213

• Manufacturer Part Number: PIC18F2431-I/SO
• Description: IC PIC MCU FLASH 8KX16 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2431-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 16KB (8K x 16)
• Package / Case: 28-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, Power Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 24
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: EUSART/I2C/SPI/SSP
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM183021, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5-ch x 10-bit
• Package: 28SOIC W
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28SO-1 - SOCKET TRANSITION 28SOIC 300MILI3-DB18F4431 - BOARD DAUGHTER ICEPIC3
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

19.3.1.1
Once the SSP module has been enabled, it waits for a
Start condition to occur. Following the Start condition,
the 8 bits are shifted into the SSPSR register. All incom-
ing bits are sampled with the rising edge of the clock
(SCL) line. The value of register SSPSR<7:1> is
compared to the value of the SSPADD register. The
address is compared on the falling edge of the eighth
clock (SCL) pulse. If the addresses match, and the BF
and SSPOV bits are clear, the following events occur:
a)
b)
c)
d)
In 10-Bit Addressing mode, two address bytes need to
be received by the slave
Significant bits (MSbs) of the first address byte specify
if this is a 10-bit address. Bit R/W (SSPSTAT<2>) must
specify a write so the slave device will receive the
second address byte. For a 10-bit address, the first
byte would equal ‘1111 0 A9 A8 0’, where A9 and
A8 are the two MSbs of the address.
TABLE 19-2:
 2010 Microchip Technology Inc.
Note:
Transfer is Received
Status Bits as Data
The SSPSR register value is loaded into the
SSPBUF register.
The Buffer Full bit, BF, is set.
An ACK pulse is generated.
SSP Interrupt Flag bit, SSPIF (PIR1<3>), is set
(interrupt is generated if enabled) on the falling
edge of the ninth SCL pulse.
BF
0
1
1
0
Shaded cells show the conditions where the user software did not properly clear the overflow condition.
Addressing
SSPOV
DATA TRANSFER RECEIVED BYTE ACTIONS
0
0
1
1
(Figure
SSPSR  SSPBUF
19-7). The five Most
Yes
No
No
No
PIC18F2331/2431/4331/4431
The sequence of events for 10-Bit Addressing mode is
as follows, with Steps 7-9 for slave-transmitter:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Generate ACK
Receive first (high) byte of address (SSPIF, BF
and UA bits are set).
Update the SSPADD register with second (low)
byte of address (clears bit, UA, and releases the
SCL line).
Read the SSPBUF register (clears bit, BF) and
clear flag bit, SSPIF.
Receive second (low) byte of address (SSPIF,
BF and UA bits are set).
Update the SSPADD register with the first (high)
byte of address. If match releases SCL line, this
will clear bit, UA.
Read the SSPBUF register (clears bit, BF) and
clear flag bit, SSPIF.
Receive Repeated Start condition.
Receive first (high) byte of address (SSPIF and
BF bits are set).
Read the SSPBUF register (clears bit, BF) and
clear flag bit, SSPIF.
Pulse
Yes
No
No
No
(SSP interrupt occurs
Set SSPIF Bit
if enabled)
DS39616D-page 213
Yes
Yes
Yes
Yes