ATMEGA645A-MUR Atmel, ATMEGA645A-MUR Datasheet - Page 318

• Manufacturer Part Number: ATMEGA645A-MUR
• Description: IC MCU AVR 64K FLASH 64QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA645A-MUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

T
Note:
318
A
Symbol
V
I
t
ACLK
ACPD
ACIO
= -40°C to 85°C, V
1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20 mA at V
4. Although each I/O port can source more than the test conditions (20 mA at V
ATmega165A/165PA/325A/325PA/3250A/3250PA/645A/645P/645
at V
observed:
TQFP and QFN/MLF Package:
1] The sum of all IOL, for all ports, should not exceed 400 mA.
2] The sum of all IOL, for ports A0 - A7, C4 - C7, G2 should not exceed 100 mA.
3] The sum of all IOL, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100 mA.
4] The sum of all IOL, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100 mA.
5] The sum of all IOL, for ports F0 - F7, should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
at V
observed:
TQFP and QFN/MLF Package:
1] The sum of all IOH, for all ports, should not exceed 400 mA.
2] The sum of all IOH, for ports A0 - A7, C4 - C7, G2 should not exceed 100 mA.
3] The sum of all IOH, for ports B0 - B7, E0 - E7, G3 - G5 should not exceed 100 mA.
4] The sum of all IOH, for ports D0 - D7, C0 - C3, G0 - G1 should not exceed 100 mA.
5] The sum of all IOH, for ports F0 - F7, should not exceed 100 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
Parameter
Analog Comparator
Input Offset Voltage
Analog Comparator
Input Leakage Current
Analog Comparator
Propagation Delay
CC
CC
= 5V, 5 mA at V
= 5V, 5 mA at V
CC
= 1.8V to 5.5V (unless otherwise noted) (Continued)
CC
CC
= 3V for all other ports) under steady state conditions (non-transient), the following must be
= 3V for all other ports) under steady state conditions (non-transient), the following must be
V
V
V
V
V
V
Condition
CC
in
CC
in
CC
CC
= V
= V
= 5V
= 5V
= 2.7V
= 4.0V
CC
CC
/2
/2
Min.
-50
CC
CC
= 5V, 10 mA at V
= 5V, 10 mA at V
Typ.
<10
750
500
CC
CC
Max.
= 3V for Port B and 10 mA
40
50
= 3V for Port B and 10mA
8285B–AVR–03/11
Units
mV
nA
ns