PIC16F819-I/ML Microchip Technology, PIC16F819-I/ML Datasheet - Page 299

• Manufacturer Part Number: PIC16F819-I/ML
• Description: IC MCU FLASH 2KX14 EEPROM 28QFN
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F819-I/ML

• Core Size: 8-Bit
• Program Memory Size: 3.5KB (2K x 14)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC16F
• No. Of I/o's: 16
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 256Byte
• Cpu Speed: 20MHz
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SPI, SSP
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28QFN3 - SOCKET TRAN ICE 18DIP/28QFNAC164322 - MODULE SOCKET MPLAB PM3 28/44QFNAC164033 - ADAPTER 28QFN TO 18DIPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Lead Free Status / Rohs Status: Details

17.4.1.3
SDA
SCL
SSPIF
BF (SSPSTAT<0>)
CKP (SSPCON1<4>)
SDA
SCL
SSPIF
1997 Microchip Technology Inc.
BF (SSPSTAT<0>)
SSPOV (SSPCON1<6>)
S
S
Slave Transmission
A7 A6 A5 A4 A3 A2 A1
1
A7
2
1
Data in
sampled
Receiving Address
3
A6
2
When the R/W bit of the incoming address byte is set and an address match occurs, the R/W bit
of the SSPSTAT register is set. The received address is loaded into the SSPBUF register. The
ACK pulse will be sent on the ninth bit, and the SCL pin is held low. The transmit data must be
loaded into the SSPBUF register, which also loads the SSPSR register. Then the SCL pin should
be enabled by setting the CKP bit (SSPCON1<4>). The master should monitor the SCL pin prior
to asserting another clock pulse. The slave devices may be holding off the master by stretching
the clock. The eight data bits are shifted out on the falling edge of the SCL input. This ensures
that the SDA signal is valid during the SCL high time
An SSP interrupt is generated for each data transfer byte. The SSPIF flag bit must be cleared in
software, and the SSPSTAT register is used to determine the status of the byte transfer. The
SSPIF flag bit is set on the falling edge of the ninth clock pulse.
As a slave-transmitter, the ACK pulse from the master-receiver is latched on the rising edge of
the ninth SCL input pulse. If the SDA line was high (not ACK), then the data transfer is complete.
When the not ACK is latched by the slave, the slave logic is reset and the slave then monitors for
another occurrence of the START bit. If the SDA line was low (ACK), the transmit data must be
loaded into the SSPBUF register, which also loads the SSPSR register. Then the SCL pin should
be enabled by setting the CKP bit.
Figure 17-12: I
Figure 17-13: I
4
A5
Receiving Address
3
5
A4
6
4
7
A3
5
R/W=0
8
A2
2
2
6
C Slave Mode Waveforms for Reception (7-bit Address)
C Slave Mode Waveforms for Transmission (7-bit Address)
ACK
9
A1
7
D7
1
D6
R/W = 1
2
8
SSPBUF register is read
Cleared in software
Preliminary
Receiving Data
D5
3
9
ACK
D4
Bit SSPOV is set because the SSPBUF register is still full.
responds to SSPIF
4
while CPU
SCL held low
D3
5
D2
6
D1
7
D7
1
SSPBUF is written in software
D0
8
Section 17. MSSP
ACK
D6
9
cleared in software
2
Set bit after writing to SSPBUF
(the SSPBUF must be written-to
before the CKP bit can be set)
D7
(Figure
1
D5
3
D6
2
D4
4
D5
Receiving Data
3
17-13).
Transmitting Data
D3
D4
4
5
ACK is not sent.
D3
D2
5
6
D2
6
From SSP interrupt
service routine
D1
7
D1
7
DS31017A-page 17-23
D0
8
D0
8
R/W = 0
ACK
ACK
9
9
transfer
Bus Master
terminates
P
P
17