AT89LP214-20XU Atmel, AT89LP214-20XU Datasheet - Page 28

• Manufacturer Part Number: AT89LP214-20XU
• Description: MCU 8051 2K FLASH 20MHZ 14-TSSOP
• Manufacturer: Atmel
• Series: 89LPr

Specifications of AT89LP214-20XU

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 12
• Program Memory Size: 2KB (2K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 14-TSSOP
• Package: 14TSSOP
• Device Core: 8051
• Family Name: AT89
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 12
• Interface Type: SPI/UART
• Number Of Timers: 2
• Core: 8051
• Processor Series: AT89x
• Maximum Clock Frequency: 20 MHz
• Data Ram Size: 128 B
• Mounting Style: SMD/SMT
• Height: 1.05 mm
• Length: 5.1 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.4 V
• Width: 4.5 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

14. Enhanced Timer/Counters
28
AT89LP213/214
Table 13-5.
The AT89LP213/214 has two 16-bit Timer/Counter registers: Timer 0 and Timer 1. As a Timer,
the register increase every clock cycle by default. Thus, the register counts clock cycles. Since a
clock cycle consists of one oscillator period, the count rate is equal to the oscillator frequency.
The timer rate can be prescaled by a value between 1 and 16 using the Timer Prescaler (see
Table 9-2 on page
As a Counter, the register is incremented in response to a l-to-0 transition at its corresponding
input pin, T0 or T1. The external input is sampled every clock cycle. When the samples show a
high in one cycle and a low in the next cycle, the count is incremented. The new count value
appears in the register during the cycle following the one in which the transition was detected.
Since 2 clock cycles are required to recognize a l-to-0 transition, the maximum count rate is 1/2
of the oscillator frequency. There are no restrictions on the duty cycle of the input signal, but it
should be held for at least one full clock cycle to ensure that a given level is sampled at least
once before it changes. In the AT89LP214, the T0 and T1 inputs are not available at the pins.
Port Pin
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
P3.0
P3.1
P3.2
P3.3
P3.4
P3.5
P3.6
Port Pin Alternate Functions
PxM0.y
P1M0.0
P1M0.1
P1M0.2
P1M0.3
P1M0.4
P1M0.5
P1M0.6
P1M0.7
P3M0.0
P3M0.1
P3M0.2
P3M0.3
P3M0.4
P3M0.5
14). Both Timers share the same prescaler.
Configuration Bits
not configurable
PxM1.y
P1M1.0
P1M1.1
P1M1.2
P1M1.3
P1M1.4
P1M1.5
P1M1.6
P1M1.7
P3M1.0
P3M1.1
P3M1.2
P3M1.3
P3M1.4
P3M1.5
Alternate
CMPOUT
Function
CLKOUT
MOSI
MISO
GPI0
GPI1
GPI2
GPI3
GPI4
GPI5
GPI6
GPI7
AIN0
AIN1
RXD
INT0
INT1
SCK
TXD
SS
T0
T1
Notes
input-only
input-only
Resets to quasi-bidirectional
AT89LP214 Only
Set as output on AT89LP213
Internal RC Oscillator Only
Internal RC Oscillator or
External Clock Source Only
AT89LP213 Only
Set as output on AT89LP214
Pin is tied to comparator output
RST must be disabled
3538E–MICRO–11/10