M30624FGAFP#U5 Renesas Electronics America, M30624FGAFP#U5 Datasheet - Page 402

• Manufacturer Part Number: M30624FGAFP#U5
• Description: IC M16C MCU FLASH 100QFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M30624FGAFP#U5

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 100-QFP
• Cpu Family: M16C
• Device Core Size: 16/32Bit
• Frequency (max): 16MHz
• Interface Type: SIM/UART
• Total Internal Ram Size: 20KB
• # I/os (max): 87
• Number Of Timers - General Purpose: 11
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.2V
• On-chip Adc: 10-chx10-bit
• On-chip Dac: 2-chx8-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -20C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: PQFP
• For Use With: 867-1000 - KIT QUICK START RENESAS 62PM3062PT3-CPE-3 - EMULATOR COMPACT M16C/62P/30P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

UART
Figure 2.5.7. UARTi-related registers (5)
UART2 special mode register
UART transmit/receive control register 2
b7 b6 b5 b4 b3 b2 b1 b0
b7
b6
0
b5
b4
b3
b2
b1
b0
Note: When using multiple pins to output the transfer clock, the following requirements must be met:
Note 1: Nothing but “0” may be written.
Note 2: When not in I
Note 3: When analog delay is selected, only the analog delay value is effective; when digital delay is selected,
ABSCS
CLKMD0
CLKMD1
ACSE
U0RRM
U1RRM
symbol
SSS
SDDS
Nothing is assigned.
In an attempt to write to this bit, write “0”. The value, if read, turns out to be indeterminate.
symbol
LSYN
U0IRS
U1IRS
Reserved bit
ABC
BBS
IICM
Bit
Bit
bit = “0”, UART2 special mode register 3 (U2SMR3 at address 0375
digital delay setup bits) are initialized to “000”, with the analog delay circuit selected. Also, when SDDS
only the digital delay value is effective.
Symbol
= “0”, the U2SMR3 register cannot be read or written to.
U2SMR
Symbol
• UART1 internal/external clock select bit (bit 3 at address 03A8
UCON
I
Arbitration lost detecting
flag control bit
Transmit start condition
select bit
SDA digital delay select
bit (Note 2, Note 3)
Bus busy flag
SCLL sync output
enable bit
Bus collision detect
sampling
clock select bit
Auto clear function
select bit of transmit
enable bit
UART0 transmit
interrupt cause select bit
UART1 transmit
interrupt cause select bit
UART0 continuous
receive mode enable bit
UART1 continuous
receive mode enable bit
CLK/CLKS select bit 0
CLK/CLKS select
bit 1 (Note)
2
C mode select bit
name
2
name
C mode, do not set this bit by writing a “1”. During normal mode, fix it to “0”. When this
Bit
Bit
Address
Address
0377
03B0
16
16
0 : Analog delay output
1 : Digital delay output
(must always be “0” when
(During clock synchronous
0 : Normal mode
1 : I
0 : Update per bit
1 : Update per byte
0 : STOP condition detected
1 : START condition detected
0 : Disabled
1 : Enabled
Must always be “0”
Must always be “0”
Must always be “0”
(During clock synchronous
0 :
1 : Transmission completed
0 :
1 : Transmission completed
0 : Continuous receive
1 : Continuous receive
0 : Continuous receive
1 : Continuous receive
Valid when bit 5 = “1”
0 : Clock output to CLK1
1 : Clock output to CLKS1
0 : Normal mode
1 : Transfer clock output
Must always be set to
not using I C mode)
is selected
is selected
Transmit buffer empty (Tl = 1)
Transmit buffer empty (Tl = 1)
(CLK output is CLK1 only)
from multiple pins
function selected
(TXEPT = 1)
(TXEPT = 1)
mode disabled
mode enable
mode disabled
mode enabled
2
C mode
serial I/O mode)
serial I/O mode)
When reset
When reset
X0000000
Function
Function
00
2
16
2
“0”
0 : Rising edge of transfer
1 : Underflow signal of timer A0
0 : Ordinary
1 : Falling edge of R
Must always be “0”
Must always be “0”
Must always be “0”
Must always be “0”
0 : No auto clear function
1 : Auto clear at occurrence of
Must always be “0”
0 : Transmit buffer empty (Tl = 1)
1 : Transmission completed
0 : Transmit buffer empty (Tl = 1)
1 : Transmission completed
Must always be “0”
Invalid
Must always be “0”
Must always be “0”
clock
bus collision
(TXEPT = 1)
(TXEPT = 1)
(During UART mode)
(During UART mode)
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
16
) = “0”.
16
) bits 7 to 5 (DL2 to DL0 = SDA
Function
Function
X
D
2
(Note1)
M16C / 62A Group
R
R
Mitsubishi microcomputers
W
W
2-83