M30624FGAFP#U5 Renesas Electronics America, M30624FGAFP#U5 Datasheet - Page 331

• Manufacturer Part Number: M30624FGAFP#U5
• Description: IC M16C MCU FLASH 100QFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M30624FGAFP#U5

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 20K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 100-QFP
• Cpu Family: M16C
• Device Core Size: 16/32Bit
• Frequency (max): 16MHz
• Interface Type: SIM/UART
• Total Internal Ram Size: 20KB
• # I/os (max): 87
• Number Of Timers - General Purpose: 11
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.2V
• On-chip Adc: 10-chx10-bit
• On-chip Dac: 2-chx8-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -20C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: PQFP
• For Use With: 867-1000 - KIT QUICK START RENESAS 62PM3062PT3-CPE-3 - EMULATOR COMPACT M16C/62P/30P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Timer A
2-12
Operation (1) Setting the count start flag to “1” causes the counter to perform a down count on the count
Figure 2.2.6. Operation timing of timer mode
2.2.2 Operation of Timer A (timer mode)
Timer Ai interrupt
request bit
Count start flag
In timer mode, choose functions from those listed in Table 2.2.1. Operations of the circled items are
described below. Figure 2.2.6 shows the operation timing, and Figure 2.2.7 shows the set-up procedure.
Table 2.2.1. Choosed functions
(2) If an underflow occurs, the content of the reload register is reloaded, and the count continues.
(3) Setting the count start flag to “0” causes the counter to hold its value and to stop.
Count source
Gate function
Pulse output function
source.
At this time, the timer Ai interrupt request bit goes to “1”.
FFFF
0000
Item
n
“1”
“0”
“1”
“0”
16
16
n = reload register content
(1) Start count
Set to “1” by software
O
O
O
Internal count source (f
No pulses output
Pulses output
No gate function
Performs count only for the period in which the TAi
Performs count only for the period in which the TAi
Cleared to “0” when interrupt request is accepted, or cleared by software
(2) Underflow
1
/ f
8
Cleared to “0” by
software
/ f
32
/ fc
32
)
Set-up
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
(3) Stop count
IN
IN
Start count again
pin is at “L” level
pin is at “H” level
Set to “1” by software
M16C / 62A Group
Mitsubishi microcomputers
Time