PIC18F2220-I/SP Microchip Technology, PIC18F2220-I/SP Datasheet - Page 81

• Manufacturer Part Number: PIC18F2220-I/SP
• Description: IC MCU FLASH 2KX16 A/D 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2220-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 4KB (2K x 16)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 25
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI/I2C/USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 5
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE4000, ICE2000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit
• Package: 28SPDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP280 - DEVICE ADAPTER 18F2220 PDIP 28LD
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

EXAMPLE 6-3:
6.5.2
Depending on the application, good programming
practice may dictate that the value written to the mem-
ory should be verified against the original value. This
should be used in applications where excessive writes
can stress bits near the specification limit.
6.5.3
If a write is terminated by an unplanned event, such as
loss of power or an unexpected Reset, the memory
location just programmed should be verified and repro-
grammed if needed. The WRERR bit is set when a
write operation is interrupted by a MCLR Reset, or a
WDT Time-out Reset, during normal operation. In
these situations, users can check the WRERR bit and
rewrite the location.
TABLE 6-2:
© 2007 Microchip Technology Inc.
TBLPTRU
TBPLTRH
TBLPTRL
TABLAT
INTCON
EECON2
EECON1
IPR2
PIR2
PIE2
Legend:
PROGRAM_MEMORY
Name
x = unknown, u = unchanged, r = reserved, - = unimplemented, read as ‘0’.
Shaded cells are not used during Flash/EEPROM access.
WRITE VERIFY
UNEXPECTED TERMINATION OF
WRITE OPERATION
Program Memory Table Pointer High Byte (TBLPTR<15:8>)
Program Memory Table Pointer High Byte (TBLPTR<7:0>)
Program Memory Table Latch
EEPROM Control Register 2 (not a physical register)
GIE/GIEH PEIE/GIEL TMR0IE
OSCFIP
OSCFIE
OSCFIF
EEPGD
Bit 7
—
REGISTERS ASSOCIATED WITH PROGRAM FLASH MEMORY
BCF
MOVLW
MOVWF
MOVLW
MOVWF
BSF
NOP
BSF
DECFSZ COUNTER_HI
GOTO
BCF
WRITING TO FLASH PROGRAM MEMORY (CONTINUED)
CFGS
CMIP
CMIF
CMIE
Bit 6
—
INTCON,GIE
55h
EECON2
AAh
EECON2
EECON1,WR
INTCON,GIE
PROGRAM_LOOP
EECON1,WREN
bit 21
Bit 5
—
—
—
—
Program Memory Table Pointer Upper Byte
(TBLPTR<20:16>)
FREE
INTE
EEIP
EEIF
EEIE
Bit 4
PIC18F2220/2320/4220/4320
WRERR
BCLIP
BCLIF
BCLIE
RBIE
Bit 3
; disable interrupts
; required sequence
; write 55H
; write AAH
; start program (CPU stall)
; re-enable interrupts
; loop until done
; disable write to memory
TMR0IF
6.6
See Section 23.0 “Special Features of the CPU”
(Section 23.5 “Program Verification and Code Pro-
tection”) for details on code protection of Flash
program memory.
WREN
LVDIP
LVDIF
LVDIE
Bit 2
Flash Program Operation During
Code Protection
TMR3IP
TMR3IF
TMR3IE
INTF
Bit 1
WR
CCP2IP
CCP2IE
CCP2IF
RBIF
Bit 0
RD
--00 0000 --00 0000
0000 0000 0000 0000
0000 0000 0000 0000
0000 0000 0000 0000
0000 000x 0000 000u
xx-0 x000 uu-0 u000
11-1 1111 ---1 1111
00-0 0000 ---0 0000
00-0 0000 ---0 0000
POR, BOR
Value on:
—
DS39599G-page 79
Value on
all other
Resets
—