C8051F321-GM Silicon Laboratories Inc, C8051F321-GM Datasheet - Page 55

• Manufacturer Part Number: C8051F321-GM
• Description: IC 8051 MCU 16K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F321-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 21
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART/USB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F320DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit or 17-ch x 10-bit
• No. Of I/o's: 21
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1480 - DAUGHTER CARD TOOLSTCK C8051F321770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1449 - ADAPTER PROGRAM TOOLSTICK F321336-1260 - DEV KIT FOR C8051F320/F321
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1261

6.
The Voltage reference MUX on C8051F320/1 devices is configurable to use an externally connected volt-
age reference, the internal reference voltage generator, or the power supply voltage VDD (see Figure 6.1).
The REFSL bit in the Reference Control register (REF0CN) selects the reference source. For the internal
reference or an external source, REFSL should be set to ‘0’; For VDD as the reference source, REFSL
should be set to ‘1’.
The BIASE bit enables the internal ADC bias generator, which is used by the ADC and Internal Oscillator.
This enable is forced to logic 1 when either of the aforementioned peripherals is enabled. The ADC bias
generator may be enabled manually by writing a ‘1’ to the BIASE bit in register REF0CN; see Figure 6.1 for
REF0CN register details. The Reference bias generator (see Figure 6.1) is used by the Internal Voltage
Reference, Temperature Sensor, and Clock Multiplier. The Reference bias is automatically enabled when
any of the aforementioned peripherals are enabled. The electrical specifications for the voltage reference
and bias circuits are given in Table 6.1.
Important Note About the VREF Input: Port pin P0.7 is used as the external VREF input. When using an
external voltage reference, P0.7 should be configured as analog input and skipped by the Digital Crossbar.
To configure P0.7 as analog input, set to ‘0’ Bit7 in register P0MDIN. To configure the Crossbar to skip
P0.7, set to ‘1’ Bit7 in register P0SKIP. Refer to Section “14. Port Input/Output” on page 126 for complete
Port I/O configuration details.
The temperature sensor connects to the ADC0 positive input multiplexer (see Section “5.1. Analog Multi-
plexer” on page 40 for details). The TEMPE bit in register REF0CN enables/disables the temperature sen-
sor. While disabled, the temperature sensor defaults to a high impedance state and any ADC0
measurements performed on the sensor result in meaningless data.
Voltage Reference
GND
VDD
R1
Reference
Figure 6.1. Voltage Reference Functional Block Diagram
External
Voltage
Circuit
VREF
VDD
REF0CN
0
1
TEMPE
Rev. 1.4
Reference
CLKMUL
REFBE
Internal
Enable
IOSCEN
AD0EN
EN
EN
EN
EN
Temp Sensor
Reference
ADC Bias
Bias
C8051F320/1
To ADC,
Internal Oscillator
To Analog Mux
(to ADC)
To Clock Multiplier,
Temp Sensor
VREF
55