C8051F321-GM Silicon Laboratories Inc, C8051F321-GM Datasheet - Page 160

• Manufacturer Part Number: C8051F321-GM
• Description: IC 8051 MCU 16K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F321-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 21
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART/USB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F320DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit or 17-ch x 10-bit
• No. Of I/o's: 21
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1480 - DAUGHTER CARD TOOLSTCK C8051F321770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1449 - ADAPTER PROGRAM TOOLSTICK F321336-1260 - DEV KIT FOR C8051F320/F321
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1261

C8051F320/1
160
Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bit2:
Bit1:
Bit0:
SSUEND SOPRDY
R/W
Bit7
USB Register Definition 15.17. E0CSR: USB0 Endpoint0 Control
INPRDY: IN Packet Ready
SSUEND: Serviced Setup End
Write: Software should set this bit to ‘1’ after servicing a Setup End (bit SUEND) event.
Hardware clears the SUEND bit when software writes ‘1’ to SSUEND.
Read: This bit always reads ‘0’.
SOPRDY: Serviced OPRDY
Write: Software should write ‘1’ to this bit after servicing a received Endpoint0 packet. The
OPRDY bit will be cleared by a write of ‘1’ to SOPRDY.
Read: This bit always reads ‘0’.
SDSTL: Send Stall
Software can write ‘1’ to this bit to terminate the current transfer (due to an error condition,
unexpected transfer request, etc.). Hardware will clear this bit to ‘0’ when the STALL hand-
shake is transmitted.
SUEND: Setup End
Hardware sets this read-only bit to ‘1’ when a control transaction ends before software has
written ‘1’ to the DATAEND bit. Hardware clears this bit when software writes ‘1’ to SSU-
END.
DATAEND: Data End
Software should write ‘1’ to this bit:
1. When writing ‘1’ to INPRDY for the last outgoing data packet.
2. When writing ‘1’ to INPRDY for a zero-length data packet.
3. When writing ‘1’ to SOPRDY after servicing the last incoming data packet.
This bit is automatically cleared by hardware.
STSTL: Sent Stall
Hardware sets this bit to ‘1’ after transmitting a STALL handshake signal. This flag must be
cleared by software.
Software should write ‘1’ to this bit after loading a data packet into the Endpoint0 FIFO for
transmit. Hardware clears this bit and generates an interrupt under either of the following
conditions:
1. The packet is transmitted.
2. The packet is overwritten by an incoming SETUP packet.
3. The packet is overwritten by an incoming OUT packet.
OPRDY: OUT Packet Ready
Hardware sets this read-only bit and generates an interrupt when a data packet has been
received. This bit is cleared only when software writes ‘1’ to the SOPRDY bit.
R/W
Bit6
SDSTL
R/W
Bit5
SUEND DATAEND
Bit4
R
Rev. 1.4
R/W
Bit3
STSTL
R/W
Bit2
INPRDY
R/W
Bit1
OPRDY
Bit0
R
USB Address:
00000000
Reset Value
0x11