C8051F321-GM Silicon Laboratories Inc, C8051F321-GM Datasheet - Page 140

• Manufacturer Part Number: C8051F321-GM
• Description: IC 8051 MCU 16K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F32xr

Specifications of C8051F321-GM

• Program Memory Type: FLASH
• Program Memory Size: 16KB (16K x 8)
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 21
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2.25 KB
• Interface Type: I2C/SMBus/SPI/UART/USB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F320DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit or 17-ch x 10-bit
• No. Of I/o's: 21
• Ram Memory Size: 1280Byte
• Cpu Speed: 25MHz
• No. Of Timers: 4
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1480 - DAUGHTER CARD TOOLSTCK C8051F321770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1449 - ADAPTER PROGRAM TOOLSTICK F321336-1260 - DEV KIT FOR C8051F320/F321
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1261

C8051F320/1
15.1. Endpoint Addressing
A total of eight endpoint pipes are available. The control endpoint (Endpoint0) always functions as a
bi-directional IN/OUT endpoint. The other endpoints are implemented as three pairs of IN/OUT endpoint
pipes:
15.2. USB Transceiver
The USB Transceiver is configured via the USB0XCN register shown in Figure 15.1. This configuration
includes Transceiver enable/disable, pull-up resistor enable/disable, and device speed selection (Full or
Low Speed). When bit SPEED = ‘1’, USB0 operates as a Full Speed USB function, and the on-chip pull-up
resistor (if enabled) appears on the D+ pin. When bit SPEED = ‘0’, USB0 operates as a Low Speed USB
function, and the on-chip pull-up resistor (if enabled) appears on the D- pin. Bits4-0 of register USB0XCN
can be used for Transceiver testing as described in Figure 15.1. The pull-up resistor is enabled only when
VBUS is present (see Section “8.2. VBUS Detection” on page 67 for details on VBUS detection).
Note: The USB clock should be active before the Transceiver is enabled.
140
Endpoint0
Endpoint1
Endpoint2
Endpoint3
Endpoint
Table 15.1. Endpoint Addressing Scheme
Associated Pipes
Endpoint0 OUT
Endpoint1 OUT
Endpoint2 OUT
Endpoint3 OUT
Endpoint0 IN
Endpoint1 IN
Endpoint2 IN
Endpoint3 IN
Rev. 1.4
USB Protocol Address
0x00
0x00
0x81
0x01
0x82
0x02
0x83
0x03