C8051F300-GM Silicon Laboratories Inc, C8051F300-GM Datasheet - Page 155

• Manufacturer Part Number: C8051F300-GM
• Description: IC 8051 MCU 8K FLASH 11QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F30xr

Specifications of C8051F300-GM

• Program Memory Type: FLASH
• Program Memory Size: 8KB (8K x 8)
• Package / Case: 11-VQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SMBus, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 8
• Number Of Timers: 3 bit
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F226DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• No. Of I/o's: 8
• Ram Memory Size: 256Byte
• Cpu Speed: 25MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• Package: 11QFN EP
• Device Core: 8051
• Family Name: C8051F30x
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1444 - ADAPTER PROGRAM TOOLSTICK F300336-1351 - KIT REF DES TEMP COMPENS RTC336-1348 - KIT STARTER TOOLSTICK336-1283 - KIT REF DESIGN DTMF DECODER336-1278 - KIT TOOL EVAL SYS IN A USB STICK336-1246 - DEV KIT F300/301/302/303/304/305
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1245

16.2.2. Software Timer (Compare) Mode
In Software Timer mode, the PCA counter/timer value is compared to the module's 16-bit capture/compare
register (PCA0CPHn and PCA0CPLn). When a match occurs, the Capture/Compare Flag (CCFn) in
PCA0CN is set to logic 1 and an interrupt request is generated if CCF interrupts are enabled. The CCFn bit
is not automatically cleared by hardware when the CPU vectors to the interrupt service routine, and must
be cleared by software. Setting the ECOMn and MATn bits in the PCA0CPMn register enables Software
Timer mode.
Important Note About Capture/Compare Registers: When writing a 16-bit value to the PCA0 Capture/
Compare registers, the low byte should always be written first. Writing to PCA0CPLn clears the ECOMn bit
to ‘0’; writing to PCA0CPHn sets ECOMn to ‘1’.
PCA0CPLn
Write to
Reset
PCA0CPHn
Write to
0
1
ENB
ENB
Figure 16.5. PCA Software Timer Mode Diagram
W
M
P
1
6
n
x
C
O
M
E
n
PCA0CPMn
C
A
P
P
n
0 0
C
N
A
P
n
M
A
T
n
O
G
T
n
0 0
W
M
P
n
C
C
E
F
n
x
Enable
PCA
Timebase
Rev. 2.6
PCA0CPLn
PCA0L
16-bit Comparator
PCA0CPHn
PCA0H
C8051F300/1/2/3/4/5
Match
C
F
C
R
PCA0CN
0
1
C
C
F
2
C
C
F
1
C
C
F
0
PCA Interrupt
155