ADUC7024BSTZ62 Analog Devices Inc, ADUC7024BSTZ62 Datasheet - Page 39

• Manufacturer Part Number: ADUC7024BSTZ62
• Description: IC MCU FLASH 62K ANLG I/O 64LQFP
• Manufacturer: Analog Devices Inc
• Series: MicroConverter® ADuC7xxxr

Specifications of ADUC7024BSTZ62

• Core Size: 16/32-Bit
• Program Memory Size: 62KB (62K x 8)
• Design Resources: Sensing Low-g Acceleration Using ADXL345 Digital Accelerometer Connected to ADuC7024 (CN0133)
• Core Processor: ARM7
• Speed: 44MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: PLA, PWM, PSM, Temp Sensor, WDT
• Number Of I /o: 30
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 10x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 64-LQFP
• Controller Family/series: (ARM7) ADUC
• No. Of I/o's: 30
• Ram Memory Size: 8KB
• Cpu Speed: 44MHz
• No. Of Timers: 4
• Digital Ic Case Style: LQFP
• Embedded Interface Type: I2C, SPI, UART
• Rohs Compliant: Yes
• Package: 64LQFP
• Device Core: ARM7TDMI
• Family Name: ADuC7xxx
• Maximum Speed: 44 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 30
• Interface Type: I2C/SPI/UART
• On-chip Adc: 10-chx12-bit
• On-chip Dac: 2-chx12-bit
• Number Of Timers: 4
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

TYPICAL OPERATION
Once configured via the ADC control and channel selection
registers, the ADC converts the analog input and provides a
12-bit result in the ADC data register.
The top 4 bits are the sign bits. The 12-bit result is placed from
Bit 16 to Bit 27 as shown in Figure 40. Again, it should be noted
that in fully differential mode, the result is represented in twos
complement format. In pseudo differential and single-ended
modes, the result is represented in straight binary format.
The same format is used in DACxDAT, simplifying the software.
Current Consumption
The ADC in standby mode, that is, powered up but not
converting, typically consumes 640 μA. The internal reference
adds 140 μA. During conversion, the extra current is 0.3 μA
multiplied by the sampling frequency (in kHz). Figure 32 shows
the current consumption vs. the sampling frequency of the ADC.
Timing
Figure 41 gives details of the ADC timing. Users control the
ADC clock speed and on the number of acquisition clocks in
the ADCCON MMR. By default, the acquisition time is eight
clocks and the clock divider is two. The number of extra clocks
(such as bit trial or write) is set to 19, which gives a sampling
rate of 774 kSPS. For conversion on temperature sensor, the
ADC acquisition time is automatically set to 16 clocks and the
ADC clock divider is set to 32. When using multiple channels
including the temperature sensor, the timing settings revert
back to the user-defined settings after reading the temperature
sensor channel.
ADC CLOCK
CONV
31
SIGN BITS
ADC
ADCDAT
START
BUSY
27
Figure 40. ADC Result Format
Figure 41. ADC Timing
ACQ
12-BIT ADC RESULT
BIT TRIAL
ADCSTA = 0
WRITE
ADC INTERRUPT
DATA
16 15
ADCSTA = 1
Rev. B | Page 39 of 92
0
ADuC7019
The ADuC7019 is identical to the ADuC7020 except for one
buffered ADC channel, ADC3, and it has only three DACs. The
output buffer of the fourth DAC is internally connected to the
ADC3 channel as shown in Figure 42.
Note that the DAC3 output pin must be connected to a 10 nF
capacitor to AGND. This channel should be used to measure dc
voltages only. ADC calibration might be necessary on this channel.
MMRS INTERFACE
The ADC is controlled and configured via the eight MMRs
described in this section.
ADCCON Register
Name
ADCCON
ADCCON is an ADC control register that allows the
programmer to enable the ADC peripheral, select the mode
of operation of the ADC (either in single-ended mode, pseudo
differential mode, or fully differential mode), and select the
conversion type. This MMR is described in Table 15.
ADuC7019/20/21/22/24/25/26/27/28
ADC3
Address
0xFFFF0500
MUX
ADC15
Figure 42. ADC3 Buffered Input
12-BIT ADC
1MSPS
Default Value
0x0600
12-BIT
ADuC7019
DAC
DAC3
Access
R/W