AT89C5132-ROTUL Atmel, AT89C5132-ROTUL Datasheet - Page 145

• Manufacturer Part Number: AT89C5132-ROTUL
• Description: IC 8051 MCU FLASH 64K USB 80TQFP
• Manufacturer: Atmel
• Series: AT89C513xr

Specifications of AT89C5132-ROTUL

• Core Processor: C52X2
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: IDE/ATAPI, I²C, MMC, PCM, SPI, UART/USART, USB
• Peripherals: I²S, POR, WDT
• Number Of I /o: 44
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.3 V
• Data Converters: A/D 2x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TQFP, 80-VQFP
• Cpu Family: 89C
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: IDE/SPI/UART/USB
• Total Internal Ram Size: 2.25KB
• # I/os (max): 44
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 3V
• Operating Supply Voltage (max): 3.3V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 2-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 80
• Package Type: TQFP
• Package: 80TQFP
• Family Name: 89C
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 3 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 44
• Number Of Timers: 2
• Maximum Clock Frequency: 20 MHz
• Data Ram Size: 2304 B
• Mounting Style: SMD/SMT
• A/d Bit Size: 10 bit
• A/d Channels Available: 2
• Height: 1.45 mm
• Length: 14.1 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 2.7 V
• Width: 14.1 mm
• For Use With: AT89OCD-01 - USB EMULATOR FOR AT8XC51 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

20.2
4173E–USB–09/07
Registers
Table 26. SSCON Register
SSCON (S:93h) – Synchronous Serial Control Register
Reset Value = 0000 0000b
Table 27. SSSTA Register
SSSTA (S:94h) – Synchronous Serial Status Register
Bit Number
SSCR2
SSC4
7
7
6
5
4
3
2
1
0
7
Mnemonic
SSCR2
SSSTO
SSCR1
SSCR0
SSSTA
SSPE
SSPE
SSAA
SSC3
SSI
Bit
6
6
Description
Synchronous Serial Control Rate Bit 2
Refer to Table 19 for rate description.
Synchronous Serial Peripheral Enable Bit
Set to enable the controller.
Clear to disable the controller.
Synchronous Serial Start Flag
Set to send a START condition on the bus.
Clear not to send a START condition on the bus.
Synchronous Serial Stop Flag
Set to send a STOP condition on the bus.
Clear not to send a STOP condition on the bus.
Synchronous Serial Interrupt Flag
Set by hardware when a serial interrupt is requested.
Must be cleared by software to acknowledge interrupt.
Synchronous Serial Assert Acknowledge Flag
Set to enable slave modes. Slave modes are entered when SLA or GCA (if SSGC set) is
recognized.
Clear to disable slave modes.
Master Receiver Mode in progress
Master Transmitter Mode in progress
Slave Receiver Mode in progress
Slave Transmitter Mode in progress
Synchronous Serial Control Rate Bit 1
Refer to Table 19 for rate description.
Synchronous Serial Control Rate Bit 0
Refer to Table 19 for rate description.
SSSTA
SSC2
Clear to force a not acknowledge (high level on SDA).
Set to force an acknowledge (low level on SDA).
This bit has no specific effect when in master transmitter mode.
Clear to force a not acknowledge (high level on SDA).
Set to force an acknowledge (low level on SDA).
Clear to isolate slave from the bus after last data Byte transmission.
Set to enable slave mode.
5
5
SSSTO
SSC1
4
4
SSC0
SSI
3
3
SSAA
2
2
0
AT89C5132
SSCR1
1
1
0
SSCR0
0
0
0
145