PIC17C43-16/P Microchip Technology, PIC17C43-16/P Datasheet - Page 101

• Manufacturer Part Number: PIC17C43-16/P
• Description: IC MCU OTP 4KX16 PWM 40DIP
• Manufacturer: Microchip Technology
• Series: PIC® 17Cr

Specifications of PIC17C43-16/P

• Core Size: 8-Bit
• Program Memory Size: 8KB (4K x 16)
• Core Processor: PIC
• Speed: 16MHz
• Connectivity: UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Type: OTP
• Ram Size: 454 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 6 V
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Controller Family/series: PIC17
• No. Of I/o's: 33
• Ram Memory Size: 454Byte
• Cpu Speed: 16MHz
• No. Of Timers: 4
• No. Of Pwm Channels: 2
• Embedded Interface Type: USART
• Rohs Compliant: Yes
• Processor Series: PIC17C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 454 B
• Interface Type: SCI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 8
• Operating Supply Voltage: 2.5 V to 6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA17XP401 - DEVICE ADAPTER FOR PIC17C42AAC174001 - MODULE SKT PROMATEII 40DIP
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

FIGURE 14-3: CRYSTAL OPERATION,
TABLE 14-2:
Higher capacitance increases the stability of the
oscillator but also increases the start-up time. These
values are for design guidance only. Since each reso-
nator has its own characteristics, the user should
consult the resonator manufacturer for appropriate
values of external components.
Resonators Used:
455 kHz
2.0 MHz
4.0 MHz
8.0 MHz
16.0 MHz
Oscillator
1996 Microchip Technology Inc.
Type
Resonators used did not have built-in capacitors.
XT
LF
C2
C1
0.1 F
To filter the fundamental frequency
Where f = tank circuit resonant frequency. This should be
midway between the fundamental and the 3rd overtone
frequencies of the crystal.
LC2
1
Panasonic EFO-A455K04B
Murata Erie CSA2.00MG
Murata Erie CSA4.00MG
Murata Erie CSA8.00MT
Murata Erie CSA16.00MX
= (2 f)
Frequency
Resonator
OVERTONE CRYSTALS (XT
OSC CONFIGURATION)
CAPACITOR SELECTION
FOR CERAMIC
RESONATORS
OSC1
OSC2
16.0 MHz
2
455 kHz
2.0 MHz
4.0 MHz
8.0 MHz
PIC17C42
Capacitor Range
33 - 100 pF
33 - 100 pF
15 - 68 pF
10 - 33 pF
22 - 68 pF
C1 = C2
SLEEP
0.3%
0.5%
0.5%
0.5%
0.5%
TABLE 14-3:
14.2.3
In the EC oscillator mode, the OSC1 input can be
driven
OSC1/CLKIN pin is hi-impedance and the OSC2/CLK-
OUT pin is the CLKOUT output (4 T
FIGURE 14-4: EXTERNAL CLOCK INPUT
Higher capacitance increases the stability of the
oscillator but also increases the start-up time and the
oscillator current. These values are for design guid-
ance only. R
overdriving the crystals with low drive level specifica-
tion. Since each crystal has its own characteristics,
the user should consult the crystal manufacturer for
appropriate values for external components.
Note 1: For V
Crystals Used:
32.768 kHz
1.0 MHz
2.0 MHz
4.0 MHz
8.0 MHz
16.0 MHz
25 MHz
32 MHz
Clock from
ext. system
Type
Osc
LF
XT
2: R
3: Only the capacitance of the board was present.
by
EXTERNAL CLOCK OSCILLATOR
mended.
bination of 15/15 pF.
CLKOUT
(F
32 MHz
S
8 MHz
32 kHz
16 MHz
25 MHz
OSC
S
1 MHz
2 MHz
2 MHz
4 MHz
of 330 is required for a capacitor com-
CMOS
Freq
may be required in XT mode to avoid
Epson C-001R32.768K-A
ECS-10-13-1
ECS-20-20-1
ECS-40-20-1
ECS ECS-80-S-4
ECS-80-18-1
ECS-160-20-1
CTS CTS25M
CRYSTEK HF-2
DD
/4)
CAPACITOR SELECTION
FOR CRYSTAL OSCILLATOR
OPERATION (EC OSC
CONFIGURATION)
> 4.5V, C1 = C2 30 pF is recom-
(1)
(2)
(3)
drivers. In
100-150 pF
47-100 pF
10-33 pF
10-33 pF
15-68 pF
15-47 pF
15-47 pF
TBD
0
PIC17C4X
C1
OSC2
OSC1
(3)
PIC17CXX
OSC
DS30412C-page 101
this
).
100-150 pF
47-100 pF
10-33 pF
10-33 pF
15-68 pF
15-47 pF
15-47 pF
mode,
TBD
0
TBD
C2
20 PPM
50 PPM
50 PPM
50 PPM
50 PPM
50 PPM
50 PPM
(3)
the