AT91M40800-33AU Atmel, AT91M40800-33AU Datasheet - Page 8

• Manufacturer Part Number: AT91M40800-33AU
• Description: IC ARM7 MCU 100 LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91M40800-33AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 33MHz
• Connectivity: EBI/EMI, UART/USART
• Peripherals: POR, WDT
• Number Of I /o: 32
• Program Memory Type: ROMless
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Package: 100TQFP
• Device Core: ARM7TDMI
• Family Name: 91M
• Maximum Speed: 33 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 32
• Interface Type: EBI/USART
• Number Of Timers: 3
• Processor Series: AT91Mx
• Core: ARM7TDMI
• Data Ram Size: 8 KB
• Maximum Clock Frequency: 33 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• Eeprom Memory: 0 Bytes
• Input Output: 32
• Interface: EBI/EMI, UART/USART
• Ios: 32
• Memory Type: ROMless
• Number Of Bits: 32
• Package Type: 100-pin LQFP
• Programmable Memory: 0 Bytes
• Timers: 3-16-bit
• Voltage, Range: 1.8-3.6 V
• Cpu Family: 91M
• Device Core Size: 32b
• Frequency (max): 33MHz
• Program Memory Size: Not Required
• Total Internal Ram Size: 8KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Product Overview
Power Supply
Input/Output
Considerations
Master Clock
Reset
NRST Pin
Watchdog Reset
Emulation Function
Tri-state Mode
8
AT91X40 Series
The AT91x40 Series Microcontrollers have two types of power supply pins - VDDIO and
VDDCORE. However, the AT91M40800, the AT91M40807 and the AT91R40807 have
single-supply VDD, VDDIO and VDDCORE pins that have to be tied to the same volt-
age. For further details on power supplies and acceptable voltage range on VDD,
VDDIO and VDDCORE, refer to the product Summary Datasheet or the product Electri-
cal Characteristics datasheet.
The AT91M40807, the AT91R40807 and the AT91R40008 accept voltage levels up to
their power supply limit on the pads.
The AT91M40800 Microcontroller I/O pads are 5V-tolerant, enabling it to interface with
external 5V devices without any additional components. 5V-tolerant means that the
AT91M40800 accepts 5V (3V) on the inputs even if it is powered at 3V (2V). Refer to the
AT91M40800 Electrical Characteristics datasheet for further details.
After the reset, the peripheral I/Os are initialized as inputs to provide the user with maxi-
mum flexibility. It is recommended that in any application phase, the inputs to the
AT91X40 Series Microcontroller be held at valid logic levels to minimize the power
consumption.
The AT91X40 Series Microcontrollers have a fully static design and work on the Master
Clock (MCK), provided on the MCKI pin from an external source.
The Master Clock is also provided as an output of the device on the pin MCKO, which is
multiplexed with a general-purpose I/O line. While NRST is active, the MCKO stays low.
After the reset, the MCKO is valid and outputs an image of the MCK signal. The PIO
Controller must be programmed to use this pin as standard I/O line.
Reset restores the default states of the user interface registers (defined in the user inter-
face of each peripheral), and forces the ARM7TDMI to perform the next instruction fetch
from address zero. Except for the program counter the ARM7TDMI registers do not
have defined reset states.
NRST is active low-level input. It is asserted asynchronously, but exit from reset is syn-
chronized internally to the MCK. The signal presented on MCK must be active within the
specification for a minimum of 10 clock cycles up to the rising edge of NRST, to ensure
correct operation. The first processor fetch occurs 80 clock cycles after the rising edge
of NRST.
The watchdog can be programmed to generate an internal reset. In this case, the reset
has the same effect as the NRST pin assertion, but the pins BMS and NTRI are not
sampled. Boot Mode and Tri-state Mode are not updated. If the NRST pin is asserted
and the watchdog triggers the internal reset, the NRST pin has priority.
The AT91X40 Series provides a tri-state mode, which is used for debug purposes. This
enables the connection of an emulator probe to an application board without having to
desolder the device from the target board. In tri-state mode, all the output pin drivers of
the AT91X40 Series Microcontroller are disabled.
1354D–ATARM–08/02