ATMEGA169PV-8AU Atmel, ATMEGA169PV-8AU Datasheet - Page 173

• Manufacturer Part Number: ATMEGA169PV-8AU
• Description: IC AVR MCU 16K 8MHZ 1.8V 64-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA169PV-8AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: ATMEGA16x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI, USART, USI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 8MHz
• Total Internal Ram Size: 1KB
• # I/os (max): 54
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 2.5/3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 1.8V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 64
• Package Type: TQFP
• Package: 64TQFP
• Family Name: ATmega
• Maximum Speed: 8 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Controller Family/series: AVR MEGA
• No. Of I/o's: 54
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• Rohs Compliant: Yes
• For Use With: ATSTK600-TQFP64 - STK600 SOCKET/ADAPTER 64-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEMATAVRBFLY - KIT EVALUATION AVR BUTTERFLYATSTK502 - MOD EXPANSION AVR STARTER 500ATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

19.3.4
19.4
8018P–AVR–08/10
Frame Formats
Synchronous Clock Operation
When synchronous mode is used (UMSELn = 1), the XCK pin will be used as either clock input
(Slave) or clock output (Master). The dependency between the clock edges and data sampling
or data change is the same. The basic principle is that data input (on RxD) is sampled at the
opposite XCK clock edge of the edge the data output (TxD) is changed.
Figure 19-3. Synchronous Mode XCK Timing.
The UCPOLn bit UCRSC selects which XCK clock edge is used for data sampling and which is
used for data change. As
rising XCK edge and sampled at falling XCK edge. If UCPOLn is set, the data will be changed at
falling XCK edge and sampled at rising XCK edge.
A serial frame is defined to be one character of data bits with synchronization bits (start and stop
bits), and optionally a parity bit for error checking. The USART accepts all 30 combinations of
the following as valid frame formats:
• 1 start bit
• 5, 6, 7, 8, or 9 data bits
• no, even or odd parity bit
• 1 or 2 stop bits
A frame starts with the start bit followed by the least significant data bit. Then the next data bits,
up to a total of nine, are succeeding, ending with the most significant bit. If enabled, the parity bit
is inserted after the data bits, before the stop bits. When a complete frame is transmitted, it can
be directly followed by a new frame, or the communication line can be set to an idle (high) state.
Figure 19-4 on page 174
brackets are optional.
UCPOL = 1
UCPOL = 0
RxD / TxD
RxD / TxD
XCK
XCK
Figure 19-3
illustrates the possible combinations of the frame formats. Bits inside
shows, when UCPOLn is zero the data will be changed at
Sample
Sample
ATmega169P
173