MA240017 Microchip Technology, MA240017 Datasheet - Page 19

• Manufacturer Part Number: MA240017
• Description: MODULE PLUG-IN PIC24F16KA102 PIM
• Manufacturer: Microchip Technology
• Series: PIC®r

Specifications of MA240017

• Accessory Type: Plug-In Module (PIM) - PIC24F16KA102
• Product: Microcontroller Modules
• Data Bus Width: 16 bit
• Core Processor: PIC24F16KA102
• Operating Supply Voltage: 3 V to 3.6 V
• Development Tools By Supplier: Integrated Development Environment, Assembler, ANSI C Compiler
• Processor Series: PIC24F
• Silicon Manufacturer: Microchip
• Core Architecture: PIC
• Core Sub-architecture: PIC24
• Silicon Core Number: PIC24F
• Silicon Family Name: PIC24FxxKAxx
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: Explorer 16 (DM240001 or DM240002)
• For Use With: DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

2.4
The on-chip voltage regulator enable/disable pin
(ENVREG or DISVREG, depending on the device
family) must always be connected directly to either a
supply voltage or to ground. The particular connection
is determined by whether or not the regulator is to be
used:
• For ENVREG, tie to V
• For DISVREG, tie to ground to enable the
Refer to Section 25.2 “On-Chip Voltage Regulator”
for details on connecting and using the on-chip
regulator.
When the regulator is enabled, a low-ESR (<5Ω)
capacitor is required on the V
stabilize the voltage regulator output voltage. The
V
must use a capacitor of 10 μF, 16V connected to
ground. The type can be ceramic or tantalum. The
placement of this capacitor should be close to the
V
length not exceed 0.25 inch (6 mm). Refer to
Section 28.0
additional information.
When the regulator is disabled, the V
must be tied to a voltage supply at the V
Refer to Section 28.0 “Electrical Characteristics” for
information on V
© 2009 Microchip Technology Inc.
CAP
CAP
Note:
or to ground to disable the regulator
regulator, or to V
/V
/V
DDCORE
DDCORE
Voltage Regulator Pins
(ENVREG/DISVREG and
V
CAP
This section applies only to PIC24FJ
devices with an on-chip voltage regulator.
. It is recommended that the trace
/V
pin must not be connected to V
“Electrical
DD
DDCORE
DD
and V
to disable the regulator
DD
DDCORE
to enable the regulator,
)
Characteristics”
CAP
.
/V
CAP
DDCORE
DDCORE
/V
DDCORE
DD
pin to
level.
, and
Preliminary
pin
for
PIC24F16KA102 FAMILY
2.5
The PGECx and PGEDx pins are used for In-Circuit
Serial Programming (ICSP) and debugging purposes.
It is recommended to keep the trace length between
the ICSP connector and the ICSP pins on the device as
short as possible. If the ICSP connector is expected to
experience an ESD event, a series resistor is recom-
mended, with the value in the range of a few tens of
ohms, not to exceed 100Ω.
Pull-up resistors, series diodes and capacitors on the
PGECx and PGEDx pins are not recommended as they
will interfere with the programmer/debugger communi-
cations to the device. If such discrete components are
an application requirement, they should be removed
from the circuit during programming and debugging.
Alternatively, refer to the AC/DC characteristics and
timing requirements information in the respective
device Flash programming specification for information
on capacitive loading limits and pin input voltage high
(V
For device emulation, ensure that the “Communication
Channel
programmed into the device matches the physical con-
nections for the ICSP to MPLAB
3 or REAL ICE™.
For more information on the ICD 2, ICD 3 and REAL ICE
connection
documents that are available on the Microchip web site.
• “MPLAB
• “Using MPLAB
• “MPLAB
• “Using MPLAB
• “MPLAB
• “MPLAB
• “Using MPLAB
IH
Guide” (DS51331)
Guide” (DS51616)
(poster) (DS51749)
) and input low (V
ICSP Pins
®
®
®
®
Select”
ICD 2 In-Circuit Debugger User’s
ICD 2 Design Advisory” (DS51566)
ICD 3 Design Advisory” (DS51764)
REAL ICE™ In-Circuit Emulator User’s
requirements,
®
®
®
ICD 2” (poster) (DS51265)
ICD 3” (poster) (DS51765)
REAL ICE™ In-Circuit Emulator”
IL
(i.e.,
) requirements.
refer
PGECx/PGEDx
®
ICD 2, MPLAB
to
DS39927B-page 17
the
following
®
pins)
ICD