PNX1301 PHILIPS [NXP Semiconductors], PNX1301 Datasheet - Page 44
PNX1301
Manufacturer Part Number
PNX1301
Description
Media Processors
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.PNX1301.pdf
(548 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PNX1301EH
Manufacturer:
MARVELL
Quantity:
335
Company:
Part Number:
PNX1301EH,557
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
PNX1301EH/G(ROHS)
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
- Current page: 44 of 548
- Download datasheet (6Mb)
PNX1300/01/02/11 Data Book
1.9.7.10
Notes: 1. For best high speed SDRAM operation, 50-ohm matched PCB traces are recommended for all MM_xxx signals.
1.9.7.11
The following specifications meet the PCI Specifications, Rev. 2.1 for 33-MHz bus operation.
Notes: 1. See the timing measurement conditions in
1-18
f
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Symbol
SDRAM
on-PCI
rst-PCI
rst-clk-PCI
rst-off-PCI
CS
PD
OH
SU
IH
val-PCI (Bus)
val-PCI (ptp)
Off-PCI
su-PCI
su-PCI (ptp)
h-PCI
Symbol
1. PCI Clock skew between two PCI devices must be lower than 1.8ns instead of the 2 ns as specified in PCI
2. Equal load circuit. MM_CLK0 and MM_CLK1 are matched output buffers.
3. The center of the two rising edges on MM_CLK0, MM_CLK1 are used as the clock reference point.
4. MM_CLK0 is used as a reference clock.
2. Minimum times are measured at the package pin with the load circuit shown in
3. REG# and GNT# are point-to-point signals and have different input setup times. All other signals are bused.
4. See the timing measurement conditions in
5. RST# is asserted and de-asserted asynchronously with respect to CLK.
6. All output drivers are floated when RST# is active.
7. For the purpose of Active/Float timing measurements, the Hi-Z or ‘off’ state is defined to be when the total current delivered
2.1 specification
MM_CLK frequency
Skew between MM_CLK0, CLK1
Propagation delay of data, address, control
Output hold time of data, address and control
Input data setup time
Input data hold time
Use 27-33 ohm series terminator resistors close to PNX1300/01/02/11 in the MM_CLK0 and MM_CLK1 line only.
Propagation delay guarantee is defined from 50% point of clock edge to 50% level on D/A/C.
Output hold time guarantee is defined from 50% point of clock edge to 50% level on D/A/C.
Input setup time requirement is defined as data value 50% complete to 50% level on clock.
Input hold time requirement is defined as minimum time from 50% level on clock to 50% change on data.
with the load circuit shown in
through the component pin is less than or equal to the leakage current specification.
SDRAM interface timing for PNX1300/01/02/11 speed grades.
PCI Bus timing
Clk to signal valid delay, bused signals
Clk to signal valid delay, point-to-point signals
Float to active delay
Active to float delay
Input setup time to CLK - bused signals
Input setup time to CLK - point-to-point signals
Input hold time from CLK
Reset active time after power stable
Reset active time after CLK stable
Reset active to output float delay
PRELIMINARY SPECIFICATION
Parameter
Figure 1-6
Parameter
and
Figure
Figure
Figure
Min Max
PNX1300
2.0
1.5
0
1-4.
1-5.
143
1-7.
0.05
143
4.7
Min
PNX1301
1.5
1.5
0
166
Max
0.05
Min.
0.2
166
100
4.2
12
2
2
2
7
1
1
Min
PNX1301
1.5
1.5
0
180
Max
11
12
28
40
Figure
Max Min Max Min Max Units
0.05
166
4.2
1-8. Maximum times are measured
PNX1311
1.5
1.5
0
Philips Semiconductors
166
Units
ms
ns
ns
ns
ns
ns
ns
ns
ns
0.05
s
166
4.2
PNX1302
1.5
1.5
0
Notes
1,2,3
1,2,3
5,6,7
200
1,7
3,4
3,4
4
5
5
1
0.05
183
3.7
MHz
ns
ns
ns
ns
ns
N
o
e
s
1
2
3
3
4
4
t
Related parts for PNX1301
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
General purpose CMOS timer
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Voltage regulator diodes
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Master I-2C - bus controller with UART interface
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
BTL stereo Class-D audio amplifier with I2S input
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
3.4 W PDM input class-D audio amplifier
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
TRIODE FOR USE AS GROUNDED GRID U.H.F. AMPLIFIER
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Specific Thales (NXP : BLA0912-250,112)
Manufacturer:
Philips Semiconductors
Part Number:
Description:
Specific Thales (NXP : MX0912B251Y,114)
Manufacturer:
Philips Semiconductors