SAM3SD8B Atmel Corporation, SAM3SD8B Datasheet - Page 1007
SAM3SD8B
Manufacturer Part Number
SAM3SD8B
Description
Manufacturer
Atmel Corporation
- Current page: 1007 of 1143
- Download datasheet (20Mb)
38. Analog-to-Digital Converter (ADC)
38.1
38.2
11090A–ATARM–10-Feb-12
11090A–ATARM–10-Feb-12
Description
Embedded Characteristics
The ADC is based on a 12-bit Converter (ADC) managed by an ADC Controller. Refer to the
Block Diagram:
analog-to-digital conversions of 16 analog lines. The conversions extend from 0V to ADVREF.
The ADC supports an 10-bit or 12-bit resolution mode, and conversion results are reported in a
common register for all channels, as well as in a channel-dedicated register. Software trigger,
external trigger on rising edge of the ADTRG pin or internal triggers from Timer Counter out-
put(s) are configurable.
The comparison circuitry allows automatic detection of values below a threshold, higher than a
threshold, in a given range or outside the range, thresholds and ranges being fully configurable.
The ADC Controller internal fault output is directly connected to PWM Fault input. This input can
be asserted by means of comparison circuitry in order to immediately put the PWM outputs in a
safe state (pure combinational path).
The ADC also integrates a Sleep Mode and a conversion sequencer and connects with a PDC
channel. These features reduce both power consumption and processor intervention.
This ADC has a selectable single-ended or fully differential input and benefits from a 2-bit pro-
grammable gain. A whole set of reference voltages is generated internally from a single external
reference voltage node that may be equal to the analog supply voltage. An external decoupling
capacitance is required for noise filtering.
A digital error correction circuit based on the multi-bit redundant signed digit (RSD) algorithm is
employed in order to reduce INL and DNL errors.
Finally, the user can configure ADC timings, such as Startup Time and Tracking Time.
• Native 12-bit resolution and 10-bit resolution for low voltage operation
• Integrated Multiplexer Offering Up to 16 Independent Analog Inputs Individual Enable and
• 1 MHz Conversion Rate
• Wide Range Power Supply Operation
• Programmable Gain (1,2,4) For Maximum Full Scale Input Range 0 - VDD
• Selectable Single Ended or Differential Input Voltage
• Integrated temperature sensor
• Automatic Calibration mode
• Hardware or Software Trigger
• Drive of PWM Fault Input
• Peripheral Data Controller (PDC) Support
Disable of Each Channel
– External Trigger Pin
– Timer Counter Outputs (Corresponding TIOA Trigger)
– Internal Trigger Counter
– Trigger on Pen Contact Detection
– PWM Event Line
Figure
38-1. It also integrates a 16-to-1 analog multiplexer, making possible the
SAM3S8/SD8
SAM3S8/SD8
1007
1007
Related parts for SAM3SD8B
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
ARM-based Flash MCU
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: