ENC28J60-I/SS Microchip Technology, ENC28J60-I/SS Datasheet - Page 8

• Manufacturer Part Number: ENC28J60-I/SS
• Description: IC ETHERNET CTRLR W/SPI 28SSOP
• Manufacturer: Microchip Technology

Specifications of ENC28J60-I/SS

• Package / Case: 28-SSOP
• Controller Type: Ethernet Controller, MAC/10Base-T
• Interface: SPI
• Voltage - Supply: 3.1 V ~ 3.6 V
• Current - Supply: 160mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Input Voltage Range (max): 2.25 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 3.3 V
• Supply Current (max): 180 mA
• Package: 28SSOP
• Standard Supported: IEEE 802.3
• Communication Mode: Full Duplex|Half Duplex
• Network Interface: MII|MIIM
• Data Rate: 10 Mbps
• Host Interface: SPI
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ENC28J60
2.3
The clock out pin is provided to the system designer for
use as the host controller clock or as a clock source for
other devices in the system. The CLKOUT has an
internal prescaler which can divide the output by 1, 2,
3, 4 or 8. The CLKOUT function is enabled and the
prescaler is selected via the ECOCON register
(Register 2-1).
To create a clean clock signal, the CLKOUT pin is held
low for a period when power is first applied. After the
Power-on Reset ends, the OST will begin counting.
When the OST expires, the CLKOUT pin will begin out-
putting its default frequency of 6.25 MHz (main clock
divided by 4). At any future time that the ENC28J60 is
reset by software or the RESET pin, the CLKOUT func-
tion will not be altered (ECOCON will not change
FIGURE 2-3:
REGISTER 2-1:
DS39662C-page 6
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-3
bit 2-0
U-0
—
CLKOUT Pin
Unimplemented: Read as ‘0’
COCON2:COCON0: Clock Output Configuration bits
11x = Reserved for factory test. Do not use. Glitch prevention not assured.
101 = CLKOUT outputs main clock divided by 8 (3.125 MHz)
100 = CLKOUT outputs main clock divided by 4 (6.25 MHz)
011 = CLKOUT outputs main clock divided by 3 (8.333333 MHz)
010 = CLKOUT outputs main clock divided by 2 (12.5 MHz)
001 = CLKOUT outputs main clock divided by 1 (25 MHz)
000 = CLKOUT is disabled. The pin is driven low.
U-0
ECOCON
—
Changed
CLKOUT TRANSITION
ECOCON: CLOCK OUTPUT CONTROL REGISTER
W = Writable bit
‘1’ = Bit is set
U-0
—
80 ns to 320 ns Delay
U-0
—
Preliminary
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
value). Additionally, Power-Down mode may be
entered and the CLKOUT function will continue to
operate. When Power-Down mode is cancelled, the
OST will be reset but the CLKOUT function will
continue. When the CLKOUT function is disabled
(ECOCON = 0), the CLKOUT pin is driven low.
The CLKOUT function is designed to ensure that mini-
mum timings are preserved when the CLKOUT pin
function is enabled, disabled or the prescaler value is
changed. No high or low pulses will be outputted which
exceed the frequency specified by the ECOCON
configuration. However, when switching frequencies, a
delay between two and eight OSC1 clock periods will
occur where no clock pulses will be produced (see
Figure 2-3). During this period, CLKOUT will be held
low.
U-0
—
COCON2
R/W-1
© 2008 Microchip Technology Inc.
x = Bit is unknown
COCON1
R/W-0
COCON0
R/W-0
bit 0