LTC2408CG Linear Technology, LTC2408CG Datasheet - Page 15

• Manufacturer Part Number: LTC2408CG
• Description: IC A/D CONV 24BIT 8-CHAN 28-SSOP
• Manufacturer: Linear Technology

Specifications of LTC2408CG

• Number Of Bits: 24
• Sampling Rate (per Second): 7.5
• Data Interface: MICROWIRE™, Serial, SPI™
• Number Of Converters: 1
• Power Dissipation (max): 1mW
• Voltage Supply Source: Single Supply
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 28-SSOP (0.200", 5.30mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

APPLICATIONS
The selection of 50Hz or 60Hz rejection can also be made
by driving F
change during the sleep or data output states will not
disturb the converter operation. If the selection is made
during the conversion state, the result of the conversion in
progress may be outside specifications but the following
conversions will not be affected.
When a fundamental rejection frequency different from
50Hz or 60Hz is required or when the converter must be
synchronized with an outside source, the LTC2404/
LTC2408 can operate with an external conversion clock.
The converter automatically detects the presence of an
external clock signal at the F
oscillator. The frequency f
be at least 2560Hz (1Hz notch frequency) to be detected.
The external clock signal duty cycle is not significant as
long as the minimum and maximum specifications for the
high and low periods t
While operating with an external conversion clock of a
frequency f
than 110dB normal mode rejection in a frequency range
f
rejection as a function of the input frequency deviation
from f
Whenever an external clock is not present at the F
converter automatically activates its internal oscillator
and enters the Internal Conversion Clock mode. The
Table 4. LTC2404/LTC2408 State Duration
State
CONVERT
SLEEP
DATA OUTPUT
MAXIMUM OUTPUT
WORD RATE
EOSC
/2560 4% and its harmonics. The normal mode
EOSC
/2560 is shown in Figure 4.
EOSC
O
to an appropriate logic level. A selection
, the LTC2404/LTC2408 provide better
Operating Mode
Internal Oscillator
External Oscillator
Internal Serial Clock
External Serial Clock with
Frequency f
U
HEO
INFORMATION
EOSC
SCK
U
and t
O
kHz
pin and turns off the internal
of the external signal must
LEO
W
are observed.
F
F
F
with Frequency f
(f
F
(Internal Oscillator)
F
Frequency f
O
O
O
O
O
EOSC
= LOW (60Hz Rejection)
= HIGH (50Hz Rejection)
= External Oscillator
= LOW/HIGH
= External Oscillator with
/2560 Rejection)
U
O
pin the
EOSC
EOSC
kHz
kHz
LTC2404/LTC2408 operation will not be disturbed if the
change of conversion clock source occurs during the
sleep state or during the data output state while the
converter uses an external serial clock. If the change
occurs during the conversion state, the result of the
conversion in progress may be outside specifications but
the following conversions will not be affected. If the
change occurs during the data output state and the
converter is in the Internal SCK mode, the serial clock duty
cycle may be affected but the serial data stream will
remain valid.
Table 4 summarizes the duration of each state as a
function of F
Figure 4. LTC2404/LTC2408 Normal Mode Rejection When
Using an External Oscillator of Frequency f
INPUT FREQUENCY DEVIATION FROM NOTCH FREQUENCY (%)
Duration
133ms
160ms
20480/f
As Long As CS = HIGH Until CS = 0 and SCK
As Long As CS = LOW But Not Longer Than 1.67ms
(32 SCK cycles)
As Long As CS = LOW But Not Longer Than 256/f
(32 SCK cycles)
As Long As CS = LOW But Not Longer Than 32/f
(32 SCK cycles)
OWR
–100
–110
–120
–130
–140
–60
–70
–80
–90
–12
O
.
EOSC
t
CONVERT
–8
(In Seconds)
–4
LTC2404/LTC2408
1
t
DATAOUTPUT
0
4
in Hz
8
24048 F04
EOSC
12
SCK
EOSC
ms
15
ms