MT28C3214P2NFL-11 TET Micron Technology Inc, MT28C3214P2NFL-11 TET Datasheet - Page 22

• Manufacturer Part Number: MT28C3214P2NFL-11 TET
• Manufacturer: Micron Technology Inc

Specifications of MT28C3214P2NFL-11 TET

• Operating Temperature (max): 85C
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Not Compliant

2 Meg x 16 Page Flash 256K x 16 SRAM Combo Memory
MT28C3214P2FL_4.p65 – Rev. 4, Pub. 4/02
alone. A locked or unlocked block can be locked down
by writing the lock down command sequence, 60h fol-
lowed by 2Fh. Locked down blocks revert to the locked
state when the device is reset or powered down.
F_WP# input. When F_WP# = 0, blocks in lock down
[011] are protected from program, erase, and lock sta-
tus changes. When F_WP# = 1, the LOCK DOWN func-
tion is disabled ([111]) and locked down blocks can be
individually unlocked by a software command to the
[110] state, where they can be erased and programmed.
These blocks can then be relocked [111] and unlocked
[110], as desired, as long as F_WP# remains HIGH.
When F_WP# goes LOW, blocks that were previously
locked down return to the lock down state [011] regard-
F_WP#
The LOCK DOWN function is dependent on the
0
0
0
1
1
1
1
DQ1
0
0
1
0
0
1
1
NOTE: 1. Other locations within the configuration address space are reserved by
ITEM
Manufacturer Code (x16)
Device Code
·
·
Block Lock Configuration
·
·
·
Chip Protection Register Lock
Chip Protection Register 1
Chip Protection Register 2
DQ0
0
1
1
0
1
0
1
Top boot configuration
Bottom boot configuration
Block is unlocked
Block is locked
Block is locked down
2. “XX” specifies the block address of lock configuration.
Chip Protection Configuration Addressing
Micron for future use.
Locked (Default)
Lock Down
Lock Down
Lock Down
Unlocked
Unlocked
Disabled
Disabled
NAME
Locked
Block Locking State Transition
ERASE/PROGRAM
Table 10
Table 9
ALLOWED
22
256K x 16 SRAM COMBO MEMORY
ADDRESS
00001h
80h
81h–84h
85h–88h
00000h
XX002h
Yes
Yes
Yes
No
No
No
No
less of any changes made while F_WP# was HIGH. De-
vice reset or power-down resets all locks, including
those in lock down, to the locked state (see Table 9).
READING A BLOCK’S LOCK STATUS
read device identification mode. To enter this mode,
write 90h to the bank containing address 00h. Subse-
quent READs at block address +00002 will output the
lock status of that block. The lowest two outputs, DQ0
and DQ1, represent the lock status. DQ0 indicates the
block lock/unlock status and is set by the LOCK com-
mand and cleared by the UNLOCK command. It is also
automatically set when entering lock down. DQ1 indi-
cates lock down status and is set by the LOCK DOWN
The lock status of every block can be read in the
2
Micron Technology, Inc., reserves the right to change products or specifications without notice.
2 MEG x 16 PAGE FLASH
To [001]
To [101]
To [111]
LOCK
DATA
002Ch
44A2h
44A3h
Lock
DQ0 = 0
DQ0 = 1
DQ1 = 1
PR Lock
Factory Data
User Data
–
–
–
–
1
UNLOCK
To [000]
To [100]
To [110]
–
–
–
–
©2002, Micron Technology, Inc.
To [011]
To [111]
To [011]
To [111]
To [111]
DOWN
LOCK
–
–