2-1419130-4 TE Connectivity, 2-1419130-4 Datasheet - Page 440

• Manufacturer Part Number: 2-1419130-4
• Description: Electromechanical Relay SPDT 1A 12VDC 960Ohm Through Hole
• Manufacturer: TE Connectivity
• Type: Miniature Sealed Relayr

Specifications of 2-1419130-4

• Contact Arrangement: SPDT
• Dc Coil Voltage: 12 V
• Coil Current: 12.5 mA
• Mounting: Through Hole
• Relay Construction: Non-Latching
• Coil Voltage Dc: 12V
• Contact Form: 1 Form C
• Coil Resistance: 960Ohm
• Contact Current Rating: 1A
• Contact Material: Silver Nickel/Gold Plated
• Coil Suppression Diode: No
• Push To Test Button: No
• Led Indicator: No
• Seal: Sealed
• Product Height (mm): 10mm
• Product Depth (mm): 7.5mm
• Product Length (mm): 12.5mm
• Mounting Style: Through Hole
• Termination Style: PC Pin
• Lead Free Status / Rohs Status: Compliant

1240
Timing Mode
Timing Specifications
Timing Ranges: 1 to 1,000 sec.
Timing Adjustment: Time delay is set by connecting an appropriately rated
Accuracy: Repeat Accuracy:
Reset Time: 100 ms, max., in the timing or time-out condition.
Output Switch Data
Arrangement: 1 Form A (SPST-NO).
Rating: 5A, inductive, at nominal operating voltage.
Inrush: Not to exceed 10A for one cycle.
Max. Leakage Current: 4mA rms.
Expected Electrical Life: 10,000,000 operations at rated load.
Initial Dielectric Strength
Between Active Terminals and Outside of Case: 1,480VAC for one min.
Outline Dimensions
On-Delay – VTM-1 in-line timing module is wired in series with the load
circuit. Time delay is initiated when power is applied to the series network.
Connecting a resistor across the center terminals provides tamper-proof
setting of time delay from 1-1000 sec.
Dimensions are shown for
reference purposes only.
resistor or potentiometer between the center two
terminals. As supplied, the unit provides a nominal 1
second delay. Add 10k ohm of resistance for every
additional second of delay required. For example: 5
seconds = 40k ohms; 10 seconds = 90k ohms.
2%
Dimensions are in inches over
(millimeters) unless otherwise
specified.
Catalog 1308242
Issued 3-03
VTM-1
Specification Grade, On-Delay
Timing Module
• On-delay timing mode
• Timing from 1 to 1000 sec.
• 1A solid state SPST-NO output
• 0.25" (6.35) quick connect terminals
• Universal voltage: 24 to 240VAC/VDC
• Rated to 10 million operations
Users should thoroughly review the technical data before selecting a product part
number. It is recommended that user also seek out the pertinent approvals files of
the agencies/laboratories and review them to ensure the product meets the
requirements for a given application.
Input Data @ 25 C
Operating Voltage: Universal: 24-240VAC/VDC (19-288VAC/VDC).
Current: 2mA (max.) required to operate timer regardless of output state.
Power Requirement: 3W, max.
Transient Protection: MOV across input 2,000V for 11 s on line side of
load.
Environmental Data
Temperature Range: Storage: -40 C to +85 C.
Mechanical Data
Mounting:
Termination: 0.250 in (6.35) quick connect terminals for input line, load
Weight: 3 oz. (84g) approximately.
Ordering Information
Authorized distributors are likely to stock the following:
VTM-1
Wiring Diagram
Notes:
1. Do not operate timer
2. For a time delay of 1
Part Number
without connecting load
in series with line voltage.
second, connect a jumper
across the center two
terminals.
VTM-1
File E60363
File LR51332
Specifications and availability
subject to change.
Screw mount in horizontal or vertical position through built-in
mounting ears.
output and timing resistor connection.
On-Delay
series
Mode
Operating: -30 C to +65 C.
24-240VAC or VDC
Input Voltage
www.tycoelectronics.com
Technical support:
Refer to inside back cover.
AGASTAT