LAN9312-NZW SMSC, LAN9312-NZW Datasheet - Page 264

• Manufacturer Part Number: LAN9312-NZW
• Description: Ethernet ICs Hi Per 2 Port 10/100 Ethernet Switch
• Manufacturer: SMSC
• Type: Two Port Managed Ethernet Switchr

Specifications of LAN9312-NZW

• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Product: Ethernet Switches
• Number Of Transceivers: 1
• Standard Supported: 802.3, 802.3u
• Data Rate: 10 Mbps, 100 Mbps
• Supply Voltage (max): 3.3 V
• Supply Voltage (min): 0 V
• Supply Current (max): 186 mA, 295 mA
• Maximum Operating Temperature: + 70 C
• Package / Case: TQFP-100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Revision 1.7 (06-29-10)
BITS
8:7
6
5
4
3
2
1
0
RESERVED
PME Buffer Type (PME_TYPE)
When this bit is cleared, the PME pin functions as an open-drain buffer for
use in a wired-or configuration. When set, the PME pin is a push-pull driver.
Note:
0: PME pin open-drain output
1: PME pin push-pull driver
Wake On LAN Status (WOL_STS)
This bit indicates that a wake-up frame or magic packet was detected by the
Host MAC.
In order to clear this bit, it is required that the event in the Host MAC be
cleared as well. The event sources are described in
Management," on page
RESERVED
PME Indication (PME_IND)
The PME signal can be configured as a pulsed output or a static signal,
which is asserted upon detection of a wake-up event. When set, the PME
signal will pulse active for 50mS upon detection of a wake-up event. When
cleared, the PME signal is driven continuously upon detection of a wake-up
event.
0: PME 50mS pulse on detection of event
1: PME driven continuously on detection of event
The PME signal can be deactivated by clearing the WOL_STS bit or by
clearing the appropriate enable.
PME Polarity (PME_POL)
This bit controls the polarity of the PME signal. When set, the PME output
is an active high signal. When cleared, it is active low.
Note:
0: PME active low
1: PME active high
PME Enable (PME_EN)
When set, this bit enables the external PME signal pin. When cleared, the
external PME signal is disabled.
Note:
0: PME pin disabled
1: PME pin enabled
Device Ready (READY)
When set, this bit indicates that the LAN9312 is ready to be accessed. Upon
power-up, nRST reset, soft reset, or digital reset, the host processor may
interrogate this field as an indication that the LAN9312 has stabilized and is
fully active.
This bit can cause an interrupt if enabled.
Note:
Note:
When PME is configured as an open-drain output, the PME_POL
field of this register is ignored and the output is always active low.
When PME is configured as an open-drain output, this field is
ignored and the output is always active low.
This bit does not affect the PME_INT interrupt bit of the
Status Register
With the exception of the HW_CFG, PMT_CTRL, BYTE_TEST, and
RESET_CTL registers, read access to any internal resources is
forbidden while the READY bit is cleared. Writes to any address
are invalid until this bit is set.
This bit is identical to bit 27 of the
(HW_CFG).
46.
(INT_STS).
DESCRIPTION
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface
DATASHEET
Hardware Configuration Register
264
Section 4.3, "Power
Interrupt
NASR
NASR
R/WC
TYPE
R/W
R/W
R/W
R/W
RO
RO
RO
SMSC LAN9312
DEFAULT
Datasheet
0b
0b
0b
0b
0b
0b
-
-