MC56F8037VLH Freescale Semiconductor, MC56F8037VLH Datasheet - Page 122

• Manufacturer Part Number: MC56F8037VLH
• Description: IC DSP 16BIT DUAL 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: 56F8xxxr

Specifications of MC56F8037VLH

• Core Processor: 56800
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: CAN, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Ram Size: 4K x 16
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 16x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 64-LQFP
• Data Bus Width: 16 bit
• Processor Series: MC56F80xx
• Core: 56800E
• Numeric And Arithmetic Format: Fixed-Point
• Device Million Instructions Per Second: 32 MIPs
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 53
• Data Ram Size: 8 KB
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: MC56F8037EVM
• Interface Type: SCI, SPI, I2C
• Minimum Operating Temperature: - 40 C
• Package: 64LQFP
• Family Name: 56F8xxx
• Maximum Speed: 32 MHz
• On-chip Adc: 2(8-chx10-bit)
• On-chip Dac: 2-chx12-bit
• Number Of Timers: 5
• For Use With: MC56F8037EVM - BOARD EVAL FOR MC56F8037
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

6.3.22
See
6.3.22.1
This bit field is reserved. Each bit must be set to 0.
6.3.22.2
This field selects the alternate input source signal to feed DAC1 SYNC input.
6.3.22.3
This bit field is reserved. It must be set to 0.
122
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Section 6.3.21
Base + $19
RESET
Read
Write
000 = I/O pin (External) - Use a PSRC0 input pin as PWM source (default)
001 = TA0 (Internal) - Use Timer A0 output as PWM source
010 = ADC SAMPLE0 (Internal) - Use ADC SAMPLE0 result as PWM source
— If the ADC conversion result in SAMPLE0 is greater than the value programmed into the High Limit
— If the ADC conversion result in SAMPLE0 is less than the value programmed into the Low Limit
011 = CMPAO (Internal) - Use Comparator A output as PWM source
100 = CMPBO (Internal) - Use Comparator B output as PWM source
11x = Reserved
1x1 = Reserved
000 = PIT0 (Internal) - Use Programmable Interval Timer 0 Output as DAC SYNC input (default)
001 = PIT1 (Internal) - Use Programmable Interval Timer 1 Output as DAC SYNC input
010 = PIT2 (Internal) - Use Programmable Interval Timer 2 Output as DAC SYNC input
011 = PWM SYNC (Internal) - Use PWM reload synchronization signal as DAC SYNC input
100 = TA0 (Internal) - Use Timer A0 output as DAC SYNC input
101 = TA1 (Internal) - Use Timer A1 output as DAC SYNC input
11x = Reserved
Figure 6-26 Internal Peripheral Source Select Register for DACs (SIM_IPS1)
register HLMT0, then PWM0 is set to 0 and PWM1 is set to 1
register LLMT0, then PWM0 is set to 1 and PWM1 is set to 0
Internal Peripheral Source Select Register 1 for Digital-to-Analog
Converters (SIM_IPS1)
Reserved—Bits 15–7
Select Input Peripheral Source for SYNC Input to DAC 1
(IPS1_DSYNC1)—Bits 6–4
Reserved—Bit 3
15
0
0
for general information about Internal Peripheral Source Select registers.
14
0
0
13
0
0
12
0
0
56F8037/56F8027 Data Sheet, Rev. 7
11
0
0
10
0
0
9
0
0
8
0
0
7
0
0
6
0
IPS1_DSYNC1
5
0
4
0
3
0
0
Freescale Semiconductor
2
0
IPS1_DSYNC0
1
0
0
0