C8051F560-IQ Silicon Laboratories Inc, C8051F560-IQ Datasheet - Page 82

• Manufacturer Part Number: C8051F560-IQ
• Description: IC 8051 MCU 32K FLASH 32-QFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F56xr

Specifications of C8051F560-IQ

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 32-QFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), CAN, LIN, SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.25 V
• Data Converters: A/D 25x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: C8051F5x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2304 B
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 25
• Operating Supply Voltage: 1.8 V to 5.25 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F560DK
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1691 - KIT DEVELOPMENT FOR C8051F560
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1693

C8051F55x/56x/57x
With the CIP-51's maximum system clock at 50 MHz, it has a peak throughput of 50 MIPS. The CIP-51 has
a total of 109 instructions. The table below shows the total number of instructions that require each execu-
tion time.
Programming and Debugging Support
In-system programming of the Flash program memory and communication with on-chip debug support
logic is accomplished via the Silicon Labs 2-Wire Development Interface (C2).
The on-chip debug support logic facilitates full speed in-circuit debugging, allowing the setting of hardware
breakpoints, starting, stopping and single stepping through program execution (including interrupt service
routines), examination of the program's call stack, and reading/writing the contents of registers and mem-
ory. This method of on-chip debugging is completely non-intrusive, requiring no RAM, Stack, timers, or
other on-chip resources. C2 details can be found in Section “27. C2 Interface” on page 296.
The CIP-51 is supported by development tools from Silicon Labs and third party vendors. Silicon Labs pro-
vides an integrated development environment (IDE) including editor, debugger and programmer. The IDE's
debugger and programmer interface to the CIP-51 via the C2 interface to provide fast and efficient in-sys-
tem device programming and debugging. Third party macro assemblers and C compilers are also avail-
able.
82
Clocks to Execute
Number of Instructions
RESET
CLOCK
STOP
IDLE
1
26
ACCUMULATOR
Figure 10.1. CIP-51 Block Diagram
PROGRAM COUNTER (PC)
CONTROL
PSW
PRGM. ADDRESS REG.
LOGIC
PC INCREMENTER
POWER CONTROL
DATA POINTER
REGISTER
2
50
BUFFER
TMP1
PIPELINE
ALU
2/3
5
TMP2
Rev. 1.1
DATA BUS
DATA BUS
D8
D8
D8
3
14
A16
D8
D8
D8
D8
B REGISTER
REGISTER
INTERFACE
INTERFACE
INTERRUPT
INTERFACE
ADDRESS
MEMORY
SRAM
SFR
BUS
3/4
7
MEM_WRITE_DATA
SFR_WRITE_DATA
MEM_READ_DATA
STACK POINTER
SFR_READ_DATA
SRAM
MEM_CONTROL
EMULATION_IRQ
MEM_ADDRESS
SFR_CONTROL
SFR_ADDRESS
SYSTEM_IRQs
4
3
4/5
1
5
2
8
1