PIC18LF452-I/PT Microchip Technology, PIC18LF452-I/PT Datasheet - Page 194

• Manufacturer Part Number: PIC18LF452-I/PT
• Description: IC MCU FLASH 16KX16 A/D 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF452-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 34
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: MSSP/SPI/I2C/PSP/USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 34
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM163022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Data Rom Size: 256 B
• Height: 1 mm
• Length: 10 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2 V
• Width: 10 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18FXX2
18.2
Depending on the power source for the device voltage,
the voltage normally decreases relatively slowly. This
means that the LVD module does not need to be con-
stantly operating. To decrease the current require-
ments, the LVD circuitry only needs to be enabled for
short periods, where the voltage is checked. After
doing the check, the LVD module may be disabled.
Each time that the LVD module is enabled, the circuitry
requires some time to stabilize. After the circuitry has
stabilized, all status flags may be cleared. The module
will then indicate the proper state of the system.
FIGURE 18-4:
DS39564B-page 192
Internally Generated
Reference Stable
Internally Generated
Reference Stable
CASE 1:
CASE 2:
Enable LVD
Enable LVD
Operation
LVDIF
LVDIF
V
V
DD
DD
LOW VOLTAGE DETECT WAVEFORMS
T
T
IVRST
IVRST
LVDIF may not be set
LVDIF cleared in software,
LVDIF remains set since LVD condition still exists
The following steps are needed to set up the LVD
module:
1.
2.
3.
4.
5.
6.
Figure 18-4 shows typical waveforms that the LVD
module may be used to detect.
Write the value to the LVDL3:LVDL0 bits
(LVDCON register), which selects the desired
LVD Trip Point.
Ensure that LVD interrupts are disabled (the
LVDIE bit is cleared or the GIE bit is cleared).
Enable the LVD module (set the LVDEN bit in
the LVDCON register).
Wait for the LVD module to stabilize (the IRVST
bit to become set).
Clear the LVD interrupt flag, which may have
falsely become set until the LVD module has
stabilized (clear the LVDIF bit).
Enable the LVD interrupt (set the LVDIE and the
GIE bits).
LVDIF cleared in software
LVDIF cleared in software
2002 Microchip Technology Inc.
V
V
LVD
LVD