PIC18LF452-I/PT Microchip Technology, PIC18LF452-I/PT Datasheet - Page 186

• Manufacturer Part Number: PIC18LF452-I/PT
• Description: IC MCU FLASH 16KX16 A/D 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18LF452-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 34
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18LF
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: MSSP/SPI/I2C/PSP/USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 34
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM163022
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Data Rom Size: 256 B
• Height: 1 mm
• Length: 10 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2 V
• Width: 10 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18FXX2
The value that is in the ADRESH/ADRESL registers is
not modified for a Power-on Reset. The ADRESH/
ADRESL registers will contain unknown data after a
Power-on Reset.
After the A/D module has been configured as desired,
the selected channel must be acquired before the con-
version is started. The analog input channels must
have their corresponding TRIS bits selected as an
input. To determine acquisition time, see Section 17.1.
After this acquisition time has elapsed, the A/D conver-
sion can be started. The following steps should be
followed for doing an A/D conversion:
1.
2.
3.
4.
FIGURE 17-2:
DS39564B-page 184
Configure the A/D module:
• Configure analog pins, voltage reference and
• Select A/D input channel (ADCON0)
• Select A/D conversion clock (ADCON0)
• Turn on A/D module (ADCON0)
Configure A/D interrupt (if desired):
• Clear ADIF bit
• Set ADIE bit
• Set GIE bit
• Set PEIE bit
Wait the required acquisition time.
Start conversion:
• Set GO/DONE bit (ADCON0)
digital I/O (ADCON1)
Legend: C
V
AIN
Rs
V
I
R
SS
C
LEAKAGE
T
PIN
IC
HOLD
ANx
ANALOG INPUT MODEL
C
5 pF
PIN
= input capacitance
= threshold voltage
= leakage current at the pin due to
= interconnect resistance
= sampling switch
= sample/hold capacitance (from DAC)
various junctions
V
DD
V
V
T
T
= 0.6V
= 0.6V
I
± 500 nA
LEAKAGE
5.
6.
7.
17.1
For the A/D converter to meet its specified accuracy,
the charge holding capacitor (C
to fully charge to the input channel voltage level. The
analog input model is shown in Figure 17-2. The
source impedance (R
switch (R
required to charge the capacitor C
switch (R
(V
at the analog input (due to pin leakage current). The
maximum recommended impedance for analog
sources is 2.5 k . After the analog input channel is
selected (changed), this acquisition must be done
before the conversion can be started.
R
IC
DD
Note:
Wait for A/D conversion to complete, by either:
• Polling for the GO/DONE bit to be cleared
OR
• Waiting for the A/D interrupt
Read A/D Result registers (ADRESH/ADRESL);
clear bit ADIF if required.
For next conversion, go to step 1 or step 2 as
required. The A/D conversion time per bit is
defined as T
required before the next acquisition starts.
1k
). The source impedance affects the offset voltage
(interrupts disabled)
A/D Acquisition Requirements
SS
V
SS
When the conversion is started, the hold-
ing capacitor is disconnected from the
input pin.
DD
SS
) impedance varies over the device voltage
Sampling
Switch
) impedance directly affect the time
6V
5V
4V
3V
2V
R
SS
AD
. A minimum wait of 2 T
S
Sampling Switch
5 6 7 8 9 10 11
) and the internal sampling
2002 Microchip Technology Inc.
V
SS
C
HOLD
HOLD
= 120 pF
HOLD
) must be allowed
(k )
. The sampling
AD
is