LD4T06P0 Red Lion Controls, LD4T06P0 Datasheet - Page 8

• Manufacturer Part Number: LD4T06P0
• Description: TIMER 6 DIGIT 4.0" 120VAC RED
• Manufacturer: Red Lion Controls
• Series: LDr
• Type: Timerr

Specifications of LD4T06P0

• No. Of Digits / Alpha: 6
• Digit Height: 101mm
• Power Consumption: 26VA
• Operating Temperature Range: 0°C To +50°C
• Signal Input Type: Pulse
• Character Size: 4"
• Ip/nema Rating: IP65 / NEMA 4X
• Signal Output Type: Relay
• Accuracy: ±0.01% %
• Connection Type: Wire Leads
• Dimensions: 26"L×2.25"W×7.875"H
• Display Digit Height: 4 "
• Display Resolution: 0.001 Sec. (Minimum Digit), 1 hr. (Single Digit)
• Display Type: LED
• Function: Timer
• Material, Casing: Aluminum
• Number Of Digits: 6
• Primary Type: Electronic
• Range, Measurement: 0 to 999999
• Special Features: RS485/RS232 Communications
• Termination: Terminal Block
• Voltage, Supply: 85 to 250/11 to 16 VAC/VDC
• Supply Voltage Range: 21.6V DC To 250V DC
• Count Speed Max: 10Hz
• External Depth: 57.15mm
• External Length / Height: 200mm
• Rohs Compliant: Yes
• Counter Supply Voltage: 85-250VAC/11-16VDC
• Display Font Color: Red
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: RLC125







counts. The Timer Reset
manual or automatic timer reset occurs (See Module 4 for programming
Automatic Reset). The Input B (
Input B is activated. This selection overrides the timer inhibit function of Input
B, when the timer is programmed for Level or Edge-1 operating mode (See
Module 1 for Timer Input Operating Modes).
Input is activated. When selected as the count source, the User Input can still be
set to perform a User Function described in Module 1. In this case, the Cycle
Counter will count the number of times the selected User Function occurred.
either activates or deactivates.


5.2 MODULE 2 - C
The Timer can be programmed to Reset at each meter power-up.
When set to
This parameter selects the source from which the Cycle Counter derives
The User Input
The Output ON/OFF selections generate a count when the Setpoint output







DISPLAY





CYCLE COUNTER COUNT SOURCE

MODE
No Function
Program Mode Lock-out
Display Select
(Edge triggered)
Maintained Reset
Display Hold
Hold and Reset

, the remaining Cycle Counter parameters are not accessible.



(
TIMER RESET AT POWER-UP

CYCLE COUNTER ENABLE
USER INPUT FUNCTION
PAR
(
Cycle Counter

)




Enable
selection generates a count each time the User


)
selection generates a count when either a
) selection generates a count each time




DESCRIPTION
User Input disabled.
See Programming Mode
Access chart (Module 3).
Toggle display with each
activation.
Level active reset of the
selected value(s).
Freeze display for the selected
value(s) while allowing time or
counts to accumulate internally.
Edge triggered reset of the
selected value(s) after
storing the time or count.
Cycle Counter
Count Source
YCLE
PARAMETER MENU
C
OUNTER
Cycle Counter
Counting
Direction
8



a selection of reset, display hold, hold and reset, inhibit, or print and reset is
selected in the User Input Function menu.

the application.

Non-zero values are normally used for “down counting” applications, but can
also provide an offset value when counting up.



The User Input Assignment only applies if the cycle counter is enabled and
Bi-directional counting capability. Select the counting direction desired for
The Cycle Counter returns to this value whenever a Counter Reset occurs.
The Cycle Counter can be programmed to Reset at each meter power-up.
P





DISPLAY
Cycle Counter
ARAMETERS
Start Value


CYCLE COUNTER COUNTING DIRECTION
CYCLE COUNTER RESET AT POWER-UP
MODE
Inhibit
Display Intensity Level
(Edge Triggered)
Print Request
Print and Reset
Reset Output


USER INPUT FUNCTION (Cont’d)
CYCLE COUNTER START VALUE




USER INPUT ASSIGNMENT
Cycle Counter
Power-up
Reset At
 


(

to





DESCRIPTION
Inhibit timing or counting for the
selected value(s).
Increase intensity one level
for each activation.
Serial transmit of the active
parameters selected in the Print
Options menu (Module 5).
Same as Print Request followed
by a momentary reset of the
selected value(s).
Edge triggered deactivation of
the Setpoint Output.
)