LD4T06P0 Red Lion Controls, LD4T06P0 Datasheet - Page 11
![TIMER 6 DIGIT 4.0" 120VAC RED](/photos/6/45/64523/mfg_ld_series_sml.jpg)
LD4T06P0
Manufacturer Part Number
LD4T06P0
Description
TIMER 6 DIGIT 4.0" 120VAC RED
Manufacturer
Red Lion Controls
Series
LDr
Type
Timerr
Specifications of LD4T06P0
No. Of Digits / Alpha
6
Digit Height
101mm
Power Consumption
26VA
Operating Temperature Range
0°C To +50°C
Signal Input Type
Pulse
Character Size
4"
Ip/nema Rating
IP65 / NEMA 4X
Signal Output Type
Relay
Accuracy
±0.01% %
Connection Type
Wire Leads
Dimensions
26"L×2.25"W×7.875"H
Display Digit Height
4 "
Display Resolution
0.001 Sec. (Minimum Digit), 1 hr. (Single Digit)
Display Type
LED
Function
Timer
Material, Casing
Aluminum
Number Of Digits
6
Primary Type
Electronic
Range, Measurement
0 to 999999
Special Features
RS485/RS232 Communications
Termination
Terminal Block
Voltage, Supply
85 to 250/11 to 16 VAC/VDC
Supply Voltage Range
21.6V DC To 250V DC
Count Speed Max
10Hz
External Depth
57.15mm
External Length / Height
200mm
Rohs Compliant
Yes
Counter Supply Voltage
85-250VAC/11-16VDC
Display Font Color
Red
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
RLC125
Normally, the baud rate is set to the highest value that all of the serial
communications equipment is capable of transmitting and receiving.
other serial communications equipment on the serial link.
data word length. Set the parity bit to match that of the other serial equipment
on the serial link. The meter ignores parity when receiving data and sets the
parity bit for outgoing data. If parity is set to
to force the frame size to 10 bits.
and a value of zero can be used (RS232 applications). Otherwise, with multiple
bussed units, a unique address number must be assigned to each meter. The
node address applies specifically to RS485 applications.
5.5 MODULE 5 - S
Parameters. These parameters are used to match the serial settings of the meter
with those of the host computer or other serial device.
Set the baud rate to match that of other serial communications equipment.
Select either 7- or 8-bit data word length. Set the word length to match the
This parameter only appears when the Data Bit parameter is set to a 7-bit
Enter the serial node address. With a single unit, an address is not needed
Module 5 is the programming module for the Serial Communications
PAR
Baud Rate
METER ADDRESS
BAUD RATE
PARITY BIT
DATA BIT
to
Data Bit
, an additional stop bit is used
ERIAL
Parity Bit
PARAMETER MENU
C
OMMUNICATIONS
11
Address
Meter
in response to a Transmit Value command or a Block Print Request. Select
for a full print transmission, consisting of the meter address, mnemonics, and
parameter data. Select
parameter data only. This setting is applied to all the parameters selected in the
PRINT OPTIONS. (Note: If the meter address is 0, the address will not be sent
during a full transmission.)
Request. A print request is also referred to as a block print because more than
one parameter can be sent to a printer or computer as a block.
in the print block. All active parameters entered as
transmitted during a block print. Parameters entered as
(
setting. For example, the Cycle Counter and Cycle Counter Start values will
only be sent when the Cycle Counter is enabled. If disabled, these parameters
are inactive and will not be transmitted. Likewise, only the Setpoint parameters
that apply to the programmed Setpoint Output Action will be transmitted.
This parameter determines the formatting of data transmitted from the meter
This parameter selects the meter values transmitted in response to a Print
Selecting
The “Print All” (
Note: Inactive parameters will not be sent regardless of the print option
DISPLAY
), without having to individually select each parameter in the sublist.
Abbreviated
displays a sublist for choosing the meter parameters to appear
Setpoint Time-out
Printing
Cycle Counter
Counter Start
Setpoint OFF
DESCRIPTION
Setpoint ON
ABBREVIATED PRINTING
Timer Start
Timer Stop
P
Timer
for abbreviated print transmissions, consisting of the
ARAMETERS
PRINT OPTIONS
) option selects all meter values for transmitting
FACTORY
SETTING
Options
Print
MNEMONIC
(
in the sublist will be
TMR
CNT
SOF
STO
TST
TSP
CST
SPT
will not be sent.
)