EVAL-ADUC847QS Analog Devices Inc, EVAL-ADUC847QS Datasheet - Page 61
EVAL-ADUC847QS
Manufacturer Part Number
EVAL-ADUC847QS
Description
KIT DEV FOR ADUC847 QUICK START
Manufacturer
Analog Devices Inc
Datasheet
1.EVAL-ADUC845QSZ.pdf
(108 pages)
Specifications of EVAL-ADUC847QS
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 61 of 108
- Download datasheet (2Mb)
I
The ADuC845/ADuC847/ADuC848 support a fully licensed
I
hardware slave and software master. SDATA (Pin 27 on the
MQFP package and Pin 29 on the LFCSP package) is the data
I/O pin. SCLK (Pin 26 on the MQFP package and Pin 28 on the
LFCSP package) is the serial interface clock for the SPI interface.
The I
pin/function multiplexing. The I
the ADuC845/ADuC847/ADuC848 also includes a second
address register (I2CADD1) at SFR Address F2H with a default
power-on value of 7FH. The I
the user and is not multiplexed with any other I/O functionality
on the chip. This means that the I
used at the same time.
Table 40. I2CCON SFR Bit Designations
Bit No.
7
6
5
4
3
2
1
0
2
2
C serial interface. The I
C SERIAL INTERFACE
2
C interface on the parts is fully independent of all other
Name
MDO
MDE
MCO
MDI
I2CM
I2CRS
I2CTX
I2CI
Description
I
This data bit is used to implement a master I
the SDATA pin if the data output enable bit (MDE) is set.
I
Set by the user to enable the SDATA pin as an output (Tx).
Cleared by the user to enable the SDATA pin as an input (Rx).
I
This bit is used to implement the SCLK for a master I
the SCLK pin.
I
This data bit is used to implement a master I
this bit on an SCLK transition if the data output enable (MDE) bit is 0.
I
Set by the user to enable I
Cleared by the user to enable I
I
Set by the user to reset the I
Cleared by the user code for normal I
I
Set by the MicroConverter if the I
Cleared by the MicroConverter if the I
I
Set by the MicroConverter after a byte has been transmitted or received.
Cleared by the MicroConverter when the user code reads the I2CDAT SFR. I2CI should not be cleared by user code.
2
2
2
2
2
2
2
2
C Software Master Data Output Bit (master mode only).
C Software Output Enable Bit (master mode only).
C Software Master Clock Output Bit (master mode only).
C Software Master Data Input Bit (master mode only).
C Master/Slave Mode Bit.
C Reset Bit (slave mode only).
C Direction Transfer Bit (slave mode only).
C Interrupt Bit (slave mode only).
2
C interface is implemented as a full
2
C interface is always available to
2
C interface incorporated on
2
C and SPI interfaces can be
2
C software master mode.
2
C interface.
2
C hardware slave mode.
2
C interface is transmitting.
2
2
Rev. B | Page 61 of 108
C operation.
C interface is receiving.
2
2
C transmitter interface in software. Data written to this bit is output on
C receiver interface in software. Data on the SDATA pin is latched into
Note that when using the I
they both use the same interrupt routine (Vector Address 3BH).
When an interrupt occurs from one of these, it is necessary to
interrogate each interface to see which one has triggered the ISR
request.
The four SFRs that are used to control the I
described next.
I2CCON—I
SFR Address:
Power-On Default:
Bit Addressable:
2
C transmitter in software. Data written to this bit is output on
2
C Control Register
ADuC845/ADuC847/ADuC848
E8H
00H
Yes
2
C and SPI interfaces simultaneously,
2
C interface are
Related parts for EVAL-ADUC847QS
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
BOARD EVAL FOR SI270X-A
Manufacturer:
Silicon Laboratories Inc
Datasheet:
Part Number:
Description:
BUCK CONV REF DESIGN KIT IP1201
Manufacturer:
International Rectifier
Datasheet:
Part Number:
Description:
BOARD DEMO SYNC DUAL BUCK CNVTER
Manufacturer:
International Rectifier
Datasheet:
Part Number:
Description:
BOARD DEMO SYNC BUCK CONVETER
Manufacturer:
International Rectifier
Datasheet:
Part Number:
Description:
EVALBOARD/EB Omnidirectional microphone - Analog
Manufacturer:
Analog Devices
Datasheet:
Part Number:
Description:
EVALBOARD/EB Omnidirectional microphone - Analog
Manufacturer:
Analog Devices
Datasheet:
Part Number:
Description:
BOARD EVAL LED DRIVER LT3756
Manufacturer:
Linear Technology
Datasheet:
Part Number:
Description:
BOARD EVAL FOR AD7741/7742
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
±1.7g Dual-Axis IMEMS Accelerometer Evaluation Board
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
IC MULTIPLIER ANALOG 8-SOIC T/R
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
IC ANALOG MULTIPLIER 8-DIP
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
IC ANALOG MULTIPLIER 8-SOIC
Manufacturer:
Analog Devices Inc
Datasheet:
Part Number:
Description:
IC ANALOG MULTIPLIER 8-DIP
Manufacturer:
Analog Devices Inc
Datasheet: