EVL6566B-65W STMicroelectronics, EVL6566B-65W Datasheet - Page 22

• Manufacturer Part Number: EVL6566B-65W
• Description: BOARD EVAL FOR L6566B
• Manufacturer: STMicroelectronics

Specifications of EVL6566B-65W

• Main Purpose: AC/DC, Primary Side
• Outputs And Type: 1, Isolated
• Power - Output: 65W
• Voltage - Output: 12V
• Current - Output: 5.4A
• Voltage - Input: 90 ~ 265VAC
• Regulator Topology: Flyback
• Frequency - Switching: 80kHz
• Board Type: Fully Populated
• Utilized Ic / Part: L6566B
• Product: Power Management Modules
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-6452

Application information
Note:
22/51
Figure 9.
V
DS
T
ON
T
osc
T
FW
When the system operates in valley skipping-mode, uneven switching cycles may be
observed under some line/load conditions, due to the fact that the OFF-time of the MOSFET
is allowed to change with discrete steps of one ringing cycle, while the OFF-time needed for
cycle-by-cycle energy balance may fall in between. Thus one or more longer switching
cycles will be compensated by one or more shorter cycles and vice versa. However, this
mechanism is absolutely normal and there is no appreciable effect on the performance of
the converter or on its output voltage.
If the MOSFET is enabled to turn on but the amplitude of the signal on the ZCD pin is
smaller than the arming threshold for some reason (e.g. a heavy damping of drain
oscillations, like in some single-stage PFC topologies, or when a turn-off snubber is used),
MOSFET’s turn-on cannot be triggered. This case is identical to what happens at start-up:
at the end of the next oscillator cycle the MOSFET will be turned on, and a new switching
cycle will take place after skipping no more than one oscillator cycle.
The operation described so far does not consider the blanking time T
turn off, and actually T
met:
Equation 3
where D is the MOSFET duty cycle. If this condition is not met, things do not change
substantially: the time during which MOSFET’s turn-on is inhibited is extended beyond T
by a fraction of T
lower than the programmed value f
earlier than expected. However this is quite unusual: setting f
phenomenon can be observed at duty cycles higher than 60 %. See
block on page 35
If the voltage on the COMP pin (9) saturates high, which reveals an open control loop, an
internal pull-up keeps the ZCD pin close to 2 V during MOSFET's OFF-time to prevent noise
from false triggering the detection block. When this pull-up is active, the ZCD pin might not
be able to go below the triggering threshold, which would stop the converter. To allow auto-
restart operation, however ensuring minimum operating frequency in these conditions, the
oscillator frequency that retriggers MOSFET's turn-on is that of the external oscillator
divided by 128. Additionally, to prevent malfunction at converter's start-up, the pull-up is
disabled during the initial soft-start (see the relevant section). However, to ensure a correct
Drain ringing cycle skipping as the load is gradually reduced
T
(limit condition)
V
P
in
= P
in'
BLANK
for further implications of T
t
BLANK
. As a consequence, the maximum switching frequency will be a little
V
DS
does not come into play as long as the following condition is
T
osc
P
osc
in
= P
and valley-skipping mode may take place slightly
D
in''
< P
≤
1
in'
−
BLANK
T
BLANK
T
osc
.
t
V
DS
osc
= 150 kHz, the
T
osc
P
BLANK
Section 5.11: OVP
in
= P
in'''
after MOSFET’s
< P
in''
L6566B
osc
t