MT18VDDT12872Y-265D2 Micron Technology Inc, MT18VDDT12872Y-265D2 Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT18VDDT12872Y-265D2
Manufacturer Part Number
MT18VDDT12872Y-265D2
Description
MODULE SDRAM DDR 1GB 184DIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT18VDDT12872Y-265D2.pdf
(39 pages)
Specifications of MT18VDDT12872Y-265D2
Memory Type
DDR SDRAM
Memory Size
1GB
Speed
266MT/s
Package / Case
184-DIMM
Main Category
DRAM Module
Sub-category
DDR SDRAM
Module Type
184RDIMM
Device Core Size
72b
Organization
128Mx72
Total Density
1GByte
Chip Density
512Mb
Access Time (max)
750ps
Maximum Clock Rate
266MHz
Operating Supply Voltage (typ)
2.5V
Operating Current
2.61A
Number Of Elements
18
Operating Supply Voltage (max)
2.7V
Operating Supply Voltage (min)
2.3V
Operating Temp Range
0C to 70C
Operating Temperature Classification
Commercial
Pin Count
184
Mounting
Socket
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Table 6:
NOTE:
Table 7:
pdf: 09005aef808a331f, source: 09005aef80858037
DD18C32_64_128_256x72G.fm - Rev. E 9/04 EN
LENGTH
1. For a burst length of two, A1–Ai select the two-data-
2. For a burst length of four, A2–Ai select the four-data-
3. For a burst length of eight, A3–Ai select the eight-data-
4. Whenever a boundary of the block is reached within a
5. i = 9, 11 (256MB and 512MB);
BURST
element block; A0 selects the first access within the
block.
element block; A0–A1 select the first access within the
block.
element block; A0–A2 select the first access within the
block.
given sequence above, the following access wraps
within the block.
i = 9, 11, 12 (1GB and 2GB).
2
4
8
SPEED
-26A
-262
-265
-202
A2 A1 A0
0
0
0
0
1
1
1
1
STARTING
ADDRESS
COLUMN
Burst Definition Table
CAS Latency (CL) Table
A1 A0
0
0
1
1
0
0
1
1
0
0
1
1
A0
75
75
75
75
0
1
0
1
0
1
0
1
0
1
0
1
0
1
CLOCK FREQUENCY (MHz)
CL = 2
ALLOWABLE OPERATING
f
f
f
f
ORDER OF ACCESSES WITHIN
0-1-2-3-4-5-6-7 0-1-2-3-4-5-6-7
1-2-3-4-5-6-7-0 1-0-3-2-5-4-7-6
2-3-4-5-6-7-0-1 2-3-0-1-6-7-4-5
3-4-5-6-7-0-1-2 3-2-1-0-7-6-5-4
4-5-6-7-0-1-2-3 4-5-6-7-0-1-2-3
5-6-7-0-1-2-3-4 5-4-7-6-1-0-3-2
6-7-0-1-2-3-4-5 6-7-4-5-2-3-0-1
7-0-1-2-3-4-5-6 7-6-5-4-3-2-1-0
SEQUENTIAL
133
133
100
100
TYPE =
0-1-2-3
1-2-3-0
2-3-0-1
3-0-1-2
0-1
1-0
A BURST
75
75
75
INTERLEAVED
CL = 2.5
NA
TYPE =
0-1-2-3
1-0-3-2
2-3-0-1
3-2-1-0
f
f
f
0-1
1-0
133
133
133
256MB, 512MB, 1GB, 2GB (x72, ECC, SR)
10
Read Latency
between the registration of a READ command and the
availability of the first bit of output data. The latency
can be set to 2 or 2.5 clocks, as shown in Figure 6, CAS
Latency Diagram.
and the latency is m clocks, the data will be available
nominally coincident with clock edge n + m. Table 7,
CAS Latency (CL) Table, indicates the operating fre-
quencies at which each CAS latency setting can be
used.
known operation or incompatibility with future ver-
sions may result.
Operating Mode
MODE REGISTER SET command with bits A7–A11
(256MB); A7–A12 (512MB and 1GB); or A7–A13 (2GB)
each set to zero, and bits A0–A6 set to the desired val-
ues. A DLL reset is initiated by issuing a MODE REGIS-
TER SET command with bits A7 and A9–A11 (256MB);
A7 and A9–A12 (512MB and 1GB); or A7–A13 (2GB)
each set to zero, bit A8 set to one, and bits A0–A6 set to
the desired values.
Micron device, JEDEC specifications recommend
when a LOAD MODE REGISTER command is issued to
COMMAND
COMMAND
The READ latency is the delay, in clock cycles,
If a READ command is registered at clock edge n,
Reserved states should not be used, because un-
The normal operating mode is selected by issuing a
DQS
DQS
CK#
CK#
DQ
DQ
Micron Technology, Inc., reserves the right to change products or specifications without notice.
Figure 6: CAS Latency Diagram
CK
CK
184-PIN DDR SDRAM RDIMM
READ
READ
Burst Length = 4 in the cases shown
Shown with nominal t AC, t DQSCK, and t DQSQ
T0
T0
CL = 2
TRANSITIONING DATA
Although not required by the
CL = 2.5
NOP
NOP
T1
T1
©2004 Micron Technology, Inc. All rights reserved.
T2
NOP
NOP
T2
T2n
T2n
DON’T CARE
T3
NOP
NOP
T3
T3n
T3n