SE97BTP,547 NXP Semiconductors, SE97BTP,547 Datasheet - Page 18

• Manufacturer Part Number: SE97BTP,547
• Description: IC TEMP SENSOR DIMM 8HWSON
• Manufacturer: NXP Semiconductors

Specifications of SE97BTP,547

• Package / Case: 8-WSON (Exposed Pad), 8-HWSON
• Function: Temp Monitoring System (Sensor)
• Topology: ADC (Sigma Delta), Comparator, Register Bank
• Sensor Type: Internal
• Sensing Temperature: -40°C ~ 125°C
• Output Type: I²C™/SMBus™
• Output Alarm: Yes
• Output Fan: Yes
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Temperature Threshold: + 150 C
• Full Temp Accuracy: 2 C
• Digital Output - Bus Interface: I2C
• Digital Output - Number Of Bits: 11 bit
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 3 V
• Description/function: Temperature Sensor
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-5055-2

NXP Semiconductors
SE97B_1
Product data sheet
Fig 13. Software Write Protect (write)
Fig 14. Software Write Protect (read)
(1) Refer to
(1) Refer to
SDA
SDA
X = Don’t Care
X = Don’t Care
7.10.2.1 Permanent Write Protection (PWP)
START condition
START condition
S
S
Table 7
Table 8
0
0
slave address (memory)
slave address (memory)
1
1
Up to eight memory devices can be connected on a single I
3-bit on the hardware selectable address (A2, A1, A0) inputs. The device only responds
when the 4-bit fixed and hardware selectable bits are matched. The 8th bit is the
read/write bit. This bit is set to 1 or 0 for read and write protection, respectively.
The corresponding device acknowledges during the ninth bit time when there is a match
on the 7-bit address.
The device does not acknowledge when there is no match on the 7-bit address or when
the device is already in permanent write protection mode and is programmed with any
write protection instructions (i.e., PWP, RWP, CWP).
If the software write-protection has been set with the PWP instruction, the first 128 bytes
of the memory are permanently write-protected. This write-protection cannot be cleared
by any instruction, or by power-cycling the device. Also, once the PWP instruction has
been successfully executed, the device no longer acknowledges any instruction (with 4-bit
fixed address of 0110b) to access the write-protection settings.
regarding the exact state of the acknowledge bit.
regarding the exact state of the acknowledge bit.
1
1
0
0
A2 A1 A0
A2 A1 A0
R/W acknowledge
R/W acknowledge
0
1
A
from slave
A
from slave
Rev. 01 — 27 January 2010
X
X
X
X
dummy byte address
dummy byte address
X
X
(1)
(1)
DDR memory module temp sensor with integrated SPD
X
X
X
X
no acknowledge
acknowledge
X
X
from slave
X
X
from slave
X
X
(1)
(1)
A
A
X
X
X
X
X
X
dummy data
dummy data
2
X
X
C-bus. Each one is given a
X
X
no acknowledge
acknowledge
X
X
STOP condition
STOP condition
X
from slave
X
from slave
© NXP B.V. 2010. All rights reserved.
X
X
002aab356
002aac644
(1)
(1)
A
A
SE97B
P
P
18 of 53