FAN3268TMX Fairchild Semiconductor, FAN3268TMX Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/2/252/fairchild_semiconductor_sml.jpg)
FAN3268TMX
Manufacturer Part Number
FAN3268TMX
Description
IC BRIDGE DVR P/N-CH 2A 8SOIC
Manufacturer
Fairchild Semiconductor
Specifications of FAN3268TMX
Configuration
Half Bridge
Input Type
Inverting and Non-Inverting
Delay Time
14ns
Current - Peak
3A
Number Of Configurations
1
Number Of Outputs
2
Voltage - Supply
4.5 V ~ 18 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Operating Temperature (max)
125C
Operating Temperature (min)
-40C
Pin Count
8
Mounting
Surface Mount
Package Type
SOIC N
Case Length
5(Max)mm
Case Height
1.5(Max)mm
Screening Level
Automotive
Product
Half-Bridge Drivers
Rise Time
22 ns
Fall Time
17 ns
Propagation Delay Time
25 ns
Supply Voltage (max)
18 V
Supply Voltage (min)
4.5 V
Supply Current
1.2 mA
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
Bridge Type
Half Bridge
Minimum Operating Temperature
- 40 C
Output Current
2.4 A
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
High Side Voltage - Max (bootstrap)
-
Lead Free Status / Rohs Status
Compliant
Other names
FAN3268TMXTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
FAN3268TMX
Manufacturer:
FSC
Quantity:
1 000
© 2009 Fairchild Semiconductor Corporation
FAN3268 • Rev. 1.0.0
Layout and Connection Guidelines
The FAN3268 gate driver incorporates fast-reacting
input circuits, short propagation delays, and powerful
output stages capable of delivering current peaks over
2A to facilitate voltage transition times from under 10ns
to over 150ns. The following layout and connection
guidelines are strongly recommended:
Keep high-current output and power ground paths
separate from l ogic and enable input signals and
signal ground paths. This is especially critical when
dealing with TTL-level logic thresholds at driver
inputs and enable pins.
Keep the driver as close to the load as possible to
minimize the length of high-current traces. This
reduces the series inductance to improve high-
speed switching, while reducing the loop area that
can radiate EMI to the driver inputs and
surrounding circuitry.
If the inputs to a channel are not externally
connected, the internal 100k Ω resistors indicated
on block diagrams command a low output (channel
A) or a high output (channel B). In noisy
environments, it may be necessary to tie inputs or
enables of an unused channel to VDD or GND
using short traces to prevent noise from causing
spurious output switching.
Many high-speed power circuits can be susceptible
to noise injected from their own output or other
external sources, possibly causing output re-
triggering. These effects can be obvious if the
circuit is tested in breadboard or non-optimal circuit
layouts with long input, enable, or output leads. For
best results, make connections to all pins as short
and direct as possible.
The turn-on and turn-off current paths should be
minimized.
12
Operational Waveforms
Figure 28 shows startup waveforms for non-inverting
channel A. At power-up, the driver output for channel A
remains low until the V
on threshold, then OUTA operates in-phase with INA.
Figure 29 illustrates startup waveforms for inverting
channel B. At power-up, the driver output for channel B
is tied to V
V
OUTB operates out of phase with INB.
DD
Figure 28. Non-Inverting Startup Waveforms
voltage reaches the UVLO turn-on threshold, then
Figure 29. Inverting Startup Waveforms
DD
through an internal 100kΩ resistor until the
DD
voltage reaches the UVLO turn-
www.fairchildsemi.com